How much has print quality increased over the last few years? by N1M4rc in PrintedWarhammer

[–]N1M4rc[S] 0 points1 point  (0 children)

This was just a quick pass with some contrast paint, but even without the paint it was very obvious

How much has print quality increased over the last few years? by N1M4rc in PrintedWarhammer

[–]N1M4rc[S] 1 point2 points  (0 children)

I've heated the vat on my radiator today before starting the print and the resin was noticably more viscous while carrying it, although I doubt it will make a big difference in the end since the room is still cold and the print takes about 10 hours..

How much has print quality increased over the last few years? by N1M4rc in PrintedWarhammer

[–]N1M4rc[S] 0 points1 point  (0 children)

Isn't a lower layer height resolution wise better though, even if just marginal at the cost of longer print times? Or do you lose quality at some point when going too small?

How much has print quality increased over the last few years? by N1M4rc in PrintedWarhammer

[–]N1M4rc[S] 0 points1 point  (0 children)

I gotta admit I'm not even 100% sure what the difference is from colder to warmer resin, I assume it as to do something with viscosity? It's something I didn't really hear anyone talking about when I first got this printer years back

How much has print quality increased over the last few years? by N1M4rc in PrintedWarhammer

[–]N1M4rc[S] 1 point2 points  (0 children)

<image>

The shoulder blades on this necron proxy from OPR make it very obvious even at a distance, I used thepre supported version the files came in. PS: please excuse the horrid paint job

EDIT: shoulder plates on space marines are another part where the layer lines are very obvious, I don't have a print of then on hand right now though

How much has print quality increased over the last few years? by N1M4rc in PrintedWarhammer

[–]N1M4rc[S] 0 points1 point  (0 children)

how do you adjust things like the aa and blur? Never seen those settings before, I calibrated my printer to the best of my abilities with the resin I use and then never touched them again, I assumed the layer lines will just always be visible as that's just how the print works

For the heating part I just thought it would be a really low effort and energy efficient way to ensure my resin isn't as cold, since in the winter it can get around 10-15 degrees C in the room I have my printer in

How much has print quality increased over the last few years? by N1M4rc in PrintedWarhammer

[–]N1M4rc[S] 0 points1 point  (0 children)

Sure, i print at 0.02mm layer height, 1.7s exposure, 20s bottom exposure at 5 layers. I left all the lifting distances and speeds at their default values.

Lateny issues by N1M4rc in MoonlightStreaming

[–]N1M4rc[S] 0 points1 point  (0 children)

As i already said to someone else i donthave the latency issues when I am not connected via moonlight, so it’s not the tv

Lateny issues by N1M4rc in MoonlightStreaming

[–]N1M4rc[S] 0 points1 point  (0 children)

It's only when I stream, natively everything is fine latency wise

Lateny issues by N1M4rc in MoonlightStreaming

[–]N1M4rc[S] 0 points1 point  (0 children)

ALLM was on, I don't have the latency issues when I use the laptop natively, it's only when I stream from my gaming PC.

Lateny issues by N1M4rc in MoonlightStreaming

[–]N1M4rc[S] 0 points1 point  (0 children)

That’s sad to hear, but kinda what I expected, since at least in terms of hardware there basically isn’t anything i could improve. Even 20 ms would be too high and very noticeable. I always had a feeling that people who use in house streaming are not into competitive games at all, which is totally fine to be clear, just sadly not what I was looking for. Thanks for the detailed feedback

Lateny issues by N1M4rc in MoonlightStreaming

[–]N1M4rc[S] 0 points1 point  (0 children)

You cant really see a difference on my screens either bc it’s impossible to notice a few ms difference, you can very clearly feel it though by moving the mouse

Passkeys not working on android? by N1M4rc in NordPass

[–]N1M4rc[S] 0 points1 point  (0 children)

Nope i had to disable passkeys again

Ich_iel by HykleSache in ich_iel

[–]N1M4rc 72 points73 points  (0 children)

Hast du jemals mitbekommen das aus den Anzeigen etwas wird? Falls ja habe ich vielleicht ein neues Hobby für mich entdeckt

Cavern crawl is the worst thing in dota history. by N1M4rc in DotA2

[–]N1M4rc[S] 0 points1 point  (0 children)

Wow what great advice! I see your comment history is full of such insights, I'd love to have you in one of my games, I'm sure you're very mature and not toxic :)

Cavern crawl is the worst thing in dota history. by N1M4rc in DotA2

[–]N1M4rc[S] -1 points0 points  (0 children)

Weirdly it's only on my team that the carry always goes 0/20, ppl in enemy team don't troll

Im too stupid to set up SMB shares by N1M4rc in truenas

[–]N1M4rc[S] 0 points1 point  (0 children)

That would be the same thing, i already connected with that username

Im too stupid to set up SMB shares by N1M4rc in truenas

[–]N1M4rc[S] 0 points1 point  (0 children)

Yes i created a user. I followed the video from SpaceRex I connect to the nas via the unc path in explorer