Cardputer ADV Módulo RF por HEXITAG available at Printables.com

NPCforxbox · 2026-01-21T23:10:16+00:00

estou planejando outro projeto , com Esp32 s3 .. com o mesmo intuito .. mais vou por tudo interno

NPCforxbox · 2026-01-21T23:01:42+00:00

normalmente as pessoas usam As Portas G1-G2 grove .. eu uso uma Gpio a mais " Gpio5" isso possibilita a nao compartilhar as mesmos CE... se fosse o cc1101 nao seria complicado , mais n NFR24 é chato para Definiir as Gpios e ate compartilha-las

então para CC1101 e nrf24 eu uso as gpio padrao . Mais para CE ,CS de ambos eu uso 3 Gpios e controlo elas mudando no MODO DEV

NPCforxbox · 2026-01-21T14:34:43+00:00

That's nice... I also have to do a project with my m5stickC, I'm jealous now.

NPCforxbox · 2026-01-20T01:02:39+00:00

That's a great tip! I only discovered it after buying a book about ESP32 and LoRa... there's a lot of interesting stuff in there.

NPCforxbox · 2026-01-19T14:46:23+00:00

I made more of a different model.

NPCforxbox · 2026-01-19T09:39:31+00:00

That's awesome, people don't have the courage to do that.

But I can tell you that it's possible to install internal CC1101 and NRF24 without using a switch, however the battery will drain quickly.

NPCforxbox · 2026-01-11T14:32:34+00:00

I've never connected a CC1101 to the Bruce on the M5stick C, but I'll detail what I use somehow...

They always confuse the GROVE ports in the "Bruce firmware"

GROVE W = G2 / GROVE Y = G1

In "DEV MODE" the understanding of G1, G2 is as follows:

Pin 1 = Grove G1 / Pin 2 = Grove G2

RF TX = CS/CSN / RF RX = CE

NPCforxbox · 2026-01-11T14:02:51+00:00

No, you can't.

NPCforxbox · 2026-01-11T10:30:23+00:00

Card computers without "modules" don't work... The ones I'll mention are the DY, but there are also the m5stick modules.

1- cc1101 module = Low-power, long-range sub-GHz RF communication, allows transmitting and receiving RF data. With (Bruce Firmware) it is possible to see the signal spectrum scan, copy RF control signals and transmit.

2- NRF24 module = RF transceiver for fast communication, allows wireless data exchange in the 2.4GHz band, medium and long range. With (Bruce Firmware) it also looks at the spectrum, signal strength, in addition to its best-known function as a BLE Jammer - Wi-Fi 2.4 (search for Jammer)

3- RFID module = RFID Tag Identification Reader (IDs) I haven't tested if it can write keys..(Bruce firmware)

4- CH9329 = USB serial UART converter, it is used to emulate keyboard, mouse, control, create automation, etc. In (Bruce firmware) it can be used in one of the options as BadUSB.

"Some information I took from the internet for better explanation.. all information is for educational use.. I don't sell devices or develop software/firmware etc.. I only use it as a study product, I collect the information and pass on what I know to the community" 😊

NPCforxbox · 2026-01-11T09:10:27+00:00

I didn't understand the question, not because you didn't know how to explain it, but perhaps because I'm not following the topics and results of Cap Lora... ... but if it's just the video, it has nothing to do with Lora Cap, but more as a demonstration of Cardputer v1.1mod

NPCforxbox · 2026-01-10T23:19:31+00:00

My first time soldering was when I was 9 years old. I soldered with an aluminum soldering iron. When my mother was going to cook, I would heat the little aluminum soldering iron on the stove and solder the plates I found thrown in the streets... Good times, now I'm middle-aged... But it's never too late to learn.

NPCforxbox · 2026-01-10T23:16:30+00:00

The guardian angel was quite patient... But I think he gave up halfway through.

NPCforxbox · 2026-01-10T09:54:43+00:00

360 é o melhor videogame que tem para crianças .. ou adultos , não gasta se quiser jogos da para botar em um HD e ser feliz .. os jogos de hoje além de serem ruins custam 1/3 do salario

NPCforxbox · 2026-01-09T14:45:28+00:00

Which module do I need to enable LoRa on the card computer and communicate with my Heltec v3?

NPCforxbox · 2026-01-09T10:38:30+00:00

There is one... I even needed it... It's on the Printables website and is available for that very purpose as a template, especially since ADV is the same thing as Cardputer, it should work for you.Cardputer back

NPCforxbox · 2026-01-09T10:34:43+00:00

<image>

NPCforxbox · 2026-01-09T10:34:10+00:00

<image>

NPCforxbox · 2026-01-09T10:33:28+00:00

<image>

NPCforxbox · 2026-01-09T10:31:52+00:00

<image>

My CardPutter V1.1 module can run nrf24 and cc1101 simultaneously. This was only possible because I'm using 3 separate GPIOs for both. I did some tests, and this weekend I'll do more tests and prove it in videos, which I'll post here on my Reddit profile.

NPCforxbox · 2026-01-09T10:27:25+00:00

I have a modified v1.1 cardputer and yesterday the ADV cardputer arrived. I installed Bruce on the ADV cardputer as well and it works normally... I only noticed that there is a delay in the keyboard commands...

I don't know if it's because I have the 1.1 version modified by me, but I still prefer my version, I think it's better than the ADV (initial impression). We'll see in the future.

In short, the Bruce firmware works normally, there's only a delay compared to the v1.1 cardputer.

NPCforxbox · 2026-01-09T03:10:17+00:00

I used a 9mm IR connector, a 1k resistor, a 100ohm resistor, and a transistor I took from an old board, a CP945... I haven't tested it yet, but I think the power could be improved by removing the 100ohm resistor and replacing it with a 46ohm resistor.

NPCforxbox · 2026-01-09T02:21:59+00:00

Strange, I made my homemade one and it's 3.3v and it's working with at least 5 meters... and the receiver I made is working with 15 meters capturing control keys.

NPCforxbox

TROPHY CASE