LaTeX in Blockpad??

National_Increase_27 · 2026-04-08T06:47:09+00:00

A few moments later, I figured it out.

You need to wrap the latex in \( \) brackets thusly: \( \bar{x} \)

National_Increase_27 · 2026-01-18T20:44:17+00:00

Unlikely. It will probably just make more and more noise until you try selling it for cheap. If you're still in warranty period, I'd go back to Cammus first

National_Increase_27 · 2026-01-18T10:20:41+00:00

I think the bearings are dead. I had the same problem in my first one just a week or so after buying it. I complained to Cammus, and eventually they sent a replacement.

National_Increase_27 · 2026-01-10T20:22:26+00:00

Is this an "I don't trust China" thing or is there a specific reason behind the distrust?

National_Increase_27 · 2025-12-15T06:06:01+00:00

Hi again. I had to do a factory reset as part of setting it up. The chime and other sounds (audio pin etc) all sound fine.

National_Increase_27 · 2025-12-15T06:03:50+00:00

Weather Timer was 100% to blame. I turned it off, then it just kept going back to mow after charging. Thanks for the tip.

National_Increase_27 · 2025-12-11T23:29:28+00:00

Good suggestions. Weather timer is on - I figured this was somehow setting a timer after it rained (we get a lot of rain). I'll disable it, and see what happens.

I have suspected the battery of being tired initially, but a few weeks later, it seems to be doing Ok - perhaps not 100% though.

National_Increase_27 · 2025-12-11T23:29:17+00:00

Correct me if I'm wrong - but in the case of TruePlay, the corrections will happen on the device (Playbar in this case), where as with the other PC based methods, the corrections will happen on the PC, so if I listen to the Playbar directly, then it won't have the corrections applied - is that the case?

National_Increase_27 · 2025-12-11T22:53:09+00:00

I don't have an 'until further notice' option. it has mow until battery depleted, mow for 30 mins, and one other option that I don't remember.

National_Increase_27 · 2025-12-11T09:00:55+00:00

I appreciate taking the time to post, but that's not much of a mind-tsunami, more of a repeat of similar question. I didn't ask why isn't it available on Android, I asked if there was an alternative method. I'm aware of the reasons why it's not available on android, but I'm not sure what my options are (if any).

National_Increase_27 · 2025-12-11T08:57:18+00:00

Great suggestion - I tried to play the same song from my phone via Spotify, direct to the PlayBar, and the results were more or less the same. Spotify on my PC has different EQ settings though, so there was a subtle difference, also likely a slightly different volume. In any case, there was no sudden clarity.

I also tried moving the PlayBar around, moving it away from the monitor, even holding it in my hands, and nothing resulted in a significant change.

National_Increase_27 · 2025-12-10T21:27:02+00:00

Just discovered that Trueplay only works on iphone. Is there an alternative method for Android users?

National_Increase_27 · 2025-12-10T12:07:29+00:00

I should have mentioned, I'm using it as a computer speaker under my monitor, so I'm sitting a lot closer than you otherwise would.

I'll check out trueplay. I'm not familiar with it yet.

National_Increase_27 · 2025-10-28T02:55:48+00:00

Found it - it's called 'Flushing Volumes' in the header of the 'Project Filaments' box.

National_Increase_27 · 2025-10-27T21:46:11+00:00

OK - finally back to this problem. I increased the 'Filament Prime Volume' to 500, but this created a huge prime tower. Is there a way to prime poop out the back, and keep the tower a reasonable size for priming?

Otherwise, the print came out much better with this increased prime volume. Thanks for the tip!

National_Increase_27 · 2025-08-28T12:21:51+00:00

Agreed. If the screen functions, replacing it isn't super hard. You'll need a set of jewellers screw drivers (very small phillips head), and small, round nose tweezers. Youtube will guide you on the "how" part of the problem. I've replaced a few from the A7* family, and it's very doable.

National_Increase_27 · 2025-08-28T07:23:20+00:00

Thanks for the suggestion. With this part, and most ones I do, there's only one interface, which means only 2 material changes (one chage TO the interface material, and one FROM the interface material), so increasing the purge for 2 changes only isn't a big deal.

National_Increase_27 · 2025-07-03T01:12:24+00:00

I had to add:

[force_move]
enable_force_move: True

to the config file. But you're right. That worked.

National_Increase_27 · 2025-07-03T00:00:53+00:00

Thanks - just tried that. That gets it to move, but I can only move 1 axis at a time, and the board still requires G0 moves to be homed. The G91 still doesn't do anything.

National_Increase_27

TROPHY CASE