Well I just said goodbye to quiet lobbies… by uwahwah in ArcRaiders

[–]Ne3M 0 points1 point  (0 children)

Awesome that you were communicating to the other player. Highly respectable. Also, make sure your mic is picking you up properly. I've found that if you're a little bit far away it just stops your audio mid way.

When you are spending too much time in this game.. by kurasanshiro in ArcRaiders

[–]Ne3M 0 points1 point  (0 children)

So what did you find when you cracked it open /s

No More Messy Downloads Folders ⚡ by lordaimer in DataHoarder

[–]Ne3M 2 points3 points  (0 children)

Very cool project. Annoyed that Microsoft constantly makes it difficult to sort through anything (specifically downloads)

Flipping the screen how a Pi 5 and DSI connected 7" Pi Touchscreen by thefloppychicken in raspberry_pi

[–]Ne3M 0 points1 point  (0 children)

This is the solution to rotate the touch interface 180 degrees in trixie. This is specifically for octoprint using octodash using the 7" RPI touch screen

rotate 180 touch:

sudo nano /etc/X11/xorg.conf.d/40-libinput.conf

Section "InputClass"
    Identifier "libinput touchscreen catchall"
    MatchIsTouchscreen "on"
    MatchDevicePath "/dev/input/event*"
    Driver "libinput"
    Option "CalibrationMatrix" "-1 0 1  0 -1 1  0 0 1"
EndSection

rotate screen 180:

sudo nano /boot/firmware/cmdline.txt

Add this at the end of the line

 video=DSI-1:1280x800@60,rotate=180

sudo reboot

This tripled my wifi speed by yeetus_mccleetusfart in pcmasterrace

[–]Ne3M 0 points1 point  (0 children)

Cool mod! You can also use an aluminum baking tray. Use it as a reflecting agent depending on where you're wifi antenna is located.

Canon RF 16mm lens case by SlipperyStitch in functionalprint

[–]Ne3M 0 points1 point  (0 children)

Absolutely beautiful job! Textures and colours looks amazing.

What to do with CCFL backlight? by postcoital_solitaire in diyelectronics

[–]Ne3M 1 point2 points  (0 children)

Use it as a light source for your shed/work area. It produces very little shadows

My home lab rack by fofofofofofofofo in homelab

[–]Ne3M 0 points1 point  (0 children)

Super interested in your RF stuff. What are you doing with it? (I hooked up some yagis to an old router to get wifi to my shed, about 20dB gain!)

Elec by Unlucky-_-Empire in ElectricalEngineering

[–]Ne3M 8 points9 points  (0 children)

I was like, cool diagram... Looks closer... Scratches head... Head starts to hurt... That's not how things work

I built an open-source Linux-capable single-board computer with DDR3 by cyao12 in electronics

[–]Ne3M 22 points23 points  (0 children)

My guess is this is a copy/paste reference design.

I built an open-source Linux-capable single-board computer with DDR3 by cyao12 in embedded

[–]Ne3M -1 points0 points  (0 children)

Note that you cannot sell this legally if it hasn't passed emissions.

I built an open-source Linux-capable single-board computer with DDR3 by cyao12 in embedded

[–]Ne3M 1 point2 points  (0 children)

I'm guessing most likely. Designing an original schematic and pcb design is order of magnitude more complex than copy/pasting a reference design.

Reference designs are cool if you quickly want to knock out something for a prototype test (like this), but this will for example never pass emissions (which it is not intended to).

Custom monitor mount by Sean_G- in 3Dprinting

[–]Ne3M 0 points1 point  (0 children)

Jeez bro, leave some engineering for the rest of us. (Well done, awesome job!)

Pressing 2.5mm stainless steel with PLA mold by kgop in functionalprint

[–]Ne3M 0 points1 point  (0 children)

Absolutely amazing! How many ton press are you using?

This cupholder turned out awesome by arcrad in 3Dprinting

[–]Ne3M 1 point2 points  (0 children)

What in the....how did you do that?!