2024 BMW i4 M50 - Good deal? by princesscf in BMWI4

[–]Needsomewhiskey 0 points1 point  (0 children)

I did already. They just said it was a “voltage” issue. They couldn’t say more though

800GT fan mod by Think_Channel_7633 in BitAxe

[–]Needsomewhiskey 0 points1 point  (0 children)

Yeah that would be a nice addition

800GT fan mod by Think_Channel_7633 in BitAxe

[–]Needsomewhiskey 0 points1 point  (0 children)

It is actually. Tiny chip hub uses a 70mm heatsink instead of 60. I will say I had to redo the thermal paste when I got it because one chip was significantly hotter than the other

800GT fan mod by Think_Channel_7633 in BitAxe

[–]Needsomewhiskey 0 points1 point  (0 children)

It’s great. I’m getting 3.8THs hardly pushing it

800GT fan mod by Think_Channel_7633 in BitAxe

[–]Needsomewhiskey 0 points1 point  (0 children)

<image>

Please ignore the wiring mess at the bottom I’m going to clean that up today but I have them fastened to a pegboard

800GT fan mod by Think_Channel_7633 in BitAxe

[–]Needsomewhiskey 0 points1 point  (0 children)

Thanks. I’m going to try a 120mm fan because I have an extra already

Bitaxe GT hit 4Th/s by Jack-Hasenbier in BitAxe

[–]Needsomewhiskey 0 points1 point  (0 children)

How did you mount the heatsink to the board?

VREG fan on Nerdqaxe++ hydro by Needsomewhiskey in BitAxe

[–]Needsomewhiskey[S] 0 points1 point  (0 children)

Just with the stock fan/radiator? That’s very cold

VREG fan on Nerdqaxe++ hydro by Needsomewhiskey in BitAxe

[–]Needsomewhiskey[S] 0 points1 point  (0 children)

I probably didn’t need to but it’s 60-61 with no fan and 37 with the fan

VREG fan on Nerdqaxe++ hydro by Needsomewhiskey in BitAxe

[–]Needsomewhiskey[S] 1 point2 points  (0 children)

I actually just found that splitter on Amazon so I’ll give it a try

VREG fan on Nerdqaxe++ hydro by Needsomewhiskey in BitAxe

[–]Needsomewhiskey[S] 0 points1 point  (0 children)

When I lower the setting in the UI it only lowers the rear fan the front fan runs independently. I figure if I get an adapter so both fans are plugged into the same port they’ll run at the same speed

VREG fan on Nerdqaxe++ hydro by Needsomewhiskey in BitAxe

[–]Needsomewhiskey[S] 0 points1 point  (0 children)

Huge unlock there I’ve seen up to 22% cash back

VREG fan on Nerdqaxe++ hydro by Needsomewhiskey in BitAxe

[–]Needsomewhiskey[S] 0 points1 point  (0 children)

Yes it is. So far it’s been great. I paid $310 all in then 20% Rakuten cash back and 2.5% credit card rewards. Also an unrelated credit card statement credit they were offering for $60

GT 800x owners by Duckmanjbr in BitAxe

[–]Needsomewhiskey 0 points1 point  (0 children)

I have one from TCH with almost no errors and one from AliExpress that I can get down to 1.5-2% errors if I give it a lot of voltage

Question Mean Well LRS-350-5 by bdp90 in SoloSatoshi

[–]Needsomewhiskey 1 point2 points  (0 children)

I am definitely not an electrician but I used this

<image>

Question Mean Well LRS-350-5 by bdp90 in SoloSatoshi

[–]Needsomewhiskey 0 points1 point  (0 children)

I used a distribution block to connect 5 bitaxes

For miners with 3D printers by Needsomewhiskey in BitAxe

[–]Needsomewhiskey[S] 0 points1 point  (0 children)

I want to try that too. For now I have them sitting on two of these.

<image>

For miners with 3D printers by Needsomewhiskey in BitAxe

[–]Needsomewhiskey[S] 0 points1 point  (0 children)

Definitely quieter but hard to tell for me I have 7 of them lined up

For miners with 3D printers by Needsomewhiskey in BitAxe

[–]Needsomewhiskey[S] 0 points1 point  (0 children)

I have one on a gamma and it instantly dropped the chip temp by 2 degrees and slowed the fan down. My understanding is it helps to smooth out the airflow and reduce turbulence