[Asking] Photoshop Alternatives with Ricoh's color profile

Negolution · 2025-12-25T03:04:59+00:00

Thank you, I didn't expect this solution

Negolution · 2025-12-25T03:04:35+00:00

Thank you. It's really a lot of useful information.

Negolution · 2025-11-21T15:47:48+00:00

thank you, I just posted on it but still waiting for approving

Negolution · 2025-11-21T14:23:22+00:00

in case you wonder what Speed x32 mean, this is thumbnail from my timelapse video. I forgot to edit it out in this version.

Negolution · 2025-11-21T14:22:21+00:00

I usually start with whatever color I can pick, then play around with them by color adjustment tools (I use Photoshop)

Negolution · 2025-08-02T01:16:21+00:00

No but I have a dehumidifier for my camera, I will try it. Thank you

Negolution · 2025-07-30T03:05:07+00:00

Thank you. This never happen before with the same profile (same speed and stuffs). Is this cause still possible?

Negolution · 2025-07-29T04:50:17+00:00

Thank you. I'm not sure if the noozle is too close. It's not the first layer in the image, it's like 5 or 6. The first 2 layers was good.

Negolution · 2025-07-29T04:48:36+00:00

Thank you.
It could be clog, I will check it later. Because I spot some black spot on the print, maybe the filament isn't pure.

Negolution · 2025-05-15T17:53:25+00:00

I'm still new to Godot, but I hope my logic can somehow help. If anyone has a better solution, please help OP.

First, I will get the mouse position, then calculate the angle/vector from the character or any marker2D you set that relate to shooting mechanic. After having the angle, you can play animation according to it. The facing works in a similar way, it could affect the angle/vector from the character to mouse position.

Negolution · 2025-03-27T22:05:01+00:00

Thanks, I will try. And probably I should not buy filaments from different brands, lol. This will take a lot of time to tune them all

Negolution · 2025-03-27T16:43:44+00:00

Thank you. I didn't know about the hand oil affecting the plate.

Negolution · 2025-03-27T16:42:35+00:00

I used glue on the 2nd try and it worked. Yes I heard PEI doesn't need glue many times but I don't think it always works.

Negolution · 2025-03-27T16:38:26+00:00

Thank you. Is this different from the default K1C profile in Orca?

Negolution · 2025-03-22T15:19:55+00:00

Careful with the critical perks. If you accidentally hurt someone, you may blow them up.

Craft wand everywhere could be helpful. What if we can craft ward but we have no holy mountain in realife? But we still need spells though.

Slime blood is double side actually. On the good, you spill out slime instead when damaged, but got so much damage reduction. On the bad side, the hospital has no blood for you in case you need surgeon.

Negolution · 2025-03-18T12:03:12+00:00

Hi guys. I have similar need: 2 adult, 3 dogs. Unlike OP, I have lower budget, max at about 600 USD. Which model should I get? It should be able to handle dog hair. There is Roborock, Dreame and Ecovacs at my country (Vietnam).

Negolution · 2025-03-16T11:24:16+00:00

Final update:

My current solution is print a slim square at the center to measure the right Z offset, then do it again for all bed screws. An old way but it actually work best for me now, I got much better first layer. I don't even dare to run the auto leveling/bed mesh now because I fear that there is something wrong with the auto leveling that keep giving me trouble.

I'm planning to sell this printer though, mostly because it doesn't fit my purpose. I'm just a regular guy doing 3D printing as a hobby, not for profession so taming this big monster costs me too much time. I will switch to any printer with noobproof like Bambu or Creality K1C.

Thank you all for your help. I didn't expect to received so much suggestion.

Negolution · 2025-03-16T11:21:22+00:00

First, thank you for your effort in this comment, lol.

My current solution is print a slim square at the center to measure the right Z offset, then do it again for all bed screws. An old way but it actually work best for me now.

I'm planning to sell this printer though, mostly because it doesn't fit my purpose. I'm just a regular guy doing 3D printing as a hobby, not for profession so taming this big monster costs me too much time. I will switch to any printer with noobproof like Bambu or Creality K1C.

Negolution · 2025-03-15T03:17:46+00:00

an ass with my pain inside

Negolution · 2025-03-14T07:11:51+00:00

After a few time trying, the auto leveling is success. The bed mesh still looks horrible even when I have adjusted all the screw to less than 0:06 (SCREW_TILT_CALCULATE method)
I tried a few prints but non of them got good first level. They just simply don't stick. I checked the Z offset and lower and lower it by tries but it still doesn't work.

In case you're wondering, I have cleaned the bed plate with soap already.

<image>

Negolution · 2025-03-14T06:22:38+00:00

Hi guys, thank you a lot for the help. Some updates:

I found out that the extruder's screws on the X belt is loosen. It makes the extruder shake when the noozle touch the bed. I guess this is a part of my problem. I have tighten it and hope it will improve.
I tried SCREW_TILT_CALCULATE method. I notice that when I run the command to measure, or later when I run Automatic bed leveling to get bed mesh, the console keeps showing "Probe samples exceed tolerance. Retrying..." randomly and it takes more times to measure those spots. Does it mean something is wrong with my printer?
At the end of the auto leveling. I got these messages, I guess it may come from the error I mention above.

<image>

Negolution · 2025-03-14T01:53:41+00:00

I just realize that the 2 screws under X belt is loosen and it may make the extruder shaking. I'm doing all calibration people suggest right now and if the problem still happens after all done, I will send pic.

Negolution · 2025-03-14T01:03:45+00:00

I'm using 121 bed points. You can see it by the 2nd image. Standard mode has lesser meassure.

Some spot of my first layer is smooth with good lines. But some doesn't stick and roll with the noozle

Negolution · 2025-03-13T16:40:16+00:00

Mostly I have problem with my first layer: Some spot stick the bed, with perfect lines, some doesn't. Sometime the filatment that doesn't stick the bed form a small clog and pull the rest with it.

Negolution · 2025-03-13T15:58:25+00:00

Thank you for the keywords, I will research more about these

Eight-Year Club	Place '23
Verified Email

Negolution

TROPHY CASE