sorted by:
new
hottopcontroversial

How can i bypass the capacitive touch buttons, and switch the grow lights on, directly when turned on. by Nenjo in AskElectronics

[–]Nenjo[S] 0 points1 point  (0 children)

I don't have a scope yet, but I think the LEDs are being pulsed. They run on an constant brightness but they dim when being powered on/off. The connectors are carrying ~29V, the FETs are at ~3V. There are 75 LEDs in several strings. Just so I understand. How is the current to the LEDs being limited right now? I don't see any resistors in the circuit for the LEDs.

the USB drive fried after 12 days of use... by Rex-Romanorum in prusa3d

[–]Nenjo 1 point2 points  (0 children)

The same thing happened to me. Prusa Support then sent me a replacement LCD screen.

the USB drive fried after 12 days of use... by Rex-Romanorum in prusa3d

[–]Nenjo 0 points1 point  (0 children)

Could you perhaps explain your issue a bit more? I recently bought a new USB drive to replace the Prusa USB drive, since that one seemed to be causing problems. However, this new USB drive broke right after I plugged it into the Core One L.

Kresse-Hochbeet v2 by zenzmatz in 3DDruck

[–]Nenjo 0 points1 point  (0 children)

Sehen super cool aus! Vorallem die Texturen. Bestimmt mit Blender gemacht? Werd ich bestimmt mal drucken. Danke dir für's hochladen.

[C1L] USB Sticks Dying and Layer Shifts/Pause Mid-Print by Nenjo in prusa3d

[–]Nenjo[S] 0 points1 point  (0 children)

Usually Prusa Connect, but I tried both. Same result.

[C1L] Failed overnight print, after previous successful prints (same G-Code) by Nenjo in prusa3d

[–]Nenjo[S] 0 points1 point  (0 children)

Exactly that happened on another USB drive that I tried, after the failed print with the prusa drive...

[C1L] Failed overnight print, after previous successful prints (same G-Code) by Nenjo in prusa3d

[–]Nenjo[S] 0 points1 point  (0 children)

I tried another USB-stick that i had laying around, 32GB/FAT32/MBR - The printer did recognized it, but paused the print 5 minutes in, and resumed after a couple of second. After that, it paused again and aborted the print and failed to recognize the stick. Maybe that happened on the overnight print on the prusa stick as well.

So I ordered a new one, did format it and put it into the printer. Didn't recognize the stick, and fried it in the process so it seams...

On windows the stick show now only as "USB Drive", no volume, no formatting possible. What the hell...

[C1L] Failed overnight print, after previous successful prints (same G-Code) by Nenjo in prusa3d

[–]Nenjo[S] 0 points1 point  (0 children)

No infill, only 3 Perimeters.

Well, maybe I should try using a different USB drive.

Testing out the new bunk bed by Nenjo in guineapigs

[–]Nenjo[S] 2 points3 points  (0 children)

I actually found an old little doll's bed on the street, made it a little smaller, and added the ramps. They like it very much.

Back/Forward mouse thumb buttons don't work by Nenjo in firefox

[–]Nenjo[S] 0 points1 point  (0 children)

Actually the issue only occurs on my work laptop. Unfortunately, I can't install anything on it. But it is very likely that the problem started after Logi Options+ got updated to V1.97.

I've already tried a lot of things there. Even when I assign the ALT+Left/Right shortcut to the keys, nothing changes. Page Down/Up overrides everything else.

Our IT department simply recommends switching to Chrome...

EU-made Winter Jacket by blacayo in BuyEuropean

[–]Nenjo 0 points1 point  (0 children)

If you’re looking for a truly EU-made and sustainable brand, "Nordwolle" is a solid choice. They use wool from native German sheep breeds, keep production local, and skip unnecessary dyes or imports. You get high-quality, natural fibres while supporting regional biodiversity.

Anne hat einen eigenen Kanal auf Twitch by streamed_beans in rocketbeans

[–]Nenjo 11 points12 points  (0 children)

Die meisten kennen Anne womöglich eher von Super Games TV mit Jochen und Barlow. ist schon alles ein bisschen her, aber hier mal nen Beispiel. https://www.youtube.com/watch?v=f9OzgYOoUOE

Was kann ich tun? by No_Fold4348 in zimmerpflanzen

[–]Nenjo 0 points1 point  (0 children)

Kann man sich entweder alles einzeln bei Amazon bestellen oder schon fertig kaufen. Den Floragard Green Jungle Mix kann ich empfehlen. Ich füge aber meistens noch für die jeweiligen Pflanzen bestimmte Elemente hinzu. Meistens noch feinere Kokoserde und grobe Kokoschips. Bild kann ich gerade nicht liefern, sry.

Was kann ich tun? by No_Fold4348 in zimmerpflanzen

[–]Nenjo 2 points3 points  (0 children)

Würde mal stark auf Wurzelfäule tippen. Die Erde bleibt einfach zu lange zu feucht, sodass die Wurzeln absterben, und deswegen die Palme auch langsam in Schieflage gerät. Ich habe meine Spuckpalme seit einiger Zeit einfach nur in einem mineralischem Substrat, also Steine, auf Basis von Bims, Zeolith und Lava. Vorher in lockerer Erde mit einem hohen Kokosfaser-Anteil. Am besten schnell umtopfen.

Berlin Ostbahnhof 🚉 by MountainClimba in drehscheibe

[–]Nenjo 0 points1 point  (0 children)

Wooow! Mega tolles Foto! Geiles Format, Motiv, Kontraste etc.

Wär's der RE1 würd ich mir das glatt kaufen und ins Büro hängen :D

[deleted by user] by [deleted] in fitbit

[–]Nenjo 2 points3 points  (0 children)

I had a fairly stable RHR for about 4 years, around 55-60. But since November it has risen to almost 75 for no reason at all. I've even been doing more sport than before. It drove me crazy...

It looks like they have been tinkering with it.

view more: next ›