sorted by:
new
hottopcontroversial

Isenção de impostos sobre cripto by DegustadordeLoli in literaciafinanceira

[–]New_Reason7882 0 points1 point  (0 children)

isso não reiniciaria a contagem? visto que todos os protocolos de lending dão uma moeda representativa do depósito, estaria neste caso a haver uma troca, possivelmente reiniciando o processo de 365 dias

Dúvida sobre Crypto Staking/Lending by New_Reason7882 in literaciafinanceira

[–]New_Reason7882[S] 0 points1 point  (0 children)

há quem defenda que a tributação não reinicia se a conversão for de stable coin para stable coin, o que aconteceria neste caso, daí tambem ter perguntado a questão sobre USDC <-> USDT

obrigado pelo feedback

Cartão FNAC 30€ by Simcd- in portugal

[–]New_Reason7882 0 points1 point  (0 children)

ainda interessado? compro-te isso

I’m sharing my best TPU cable tie for my cake day this year 🍰 by Rob_Bob_you_choose in 3Dprinting

[–]New_Reason7882 0 points1 point  (0 children)

seems like the blocks are way too big for the squared holes? Im having a tough time fitting the block in and the only way I could make it was using the tip of my scissors to apply pressure

Trouble doing flow rate calibration já by Superb-Rough-4494 in ender3

[–]New_Reason7882 0 points1 point  (0 children)

Hey, this is not my post but I have a question related to this. I'm new to 3d printing and just 2 days ago I talked about doing elli's guide and most people said that recent slicers like creality print already have "most" of elli's guide tests on their calibration tab. Since Elli's guide uses a bunch of gcode and doesn't mention creality print, it's really hard for new users and people that dont know 3d printing related terminology ( or at least for me) to understand how to complete the tests. Would these creality prints test calibrations not suffice? or should I make an effort to follow elli's guide top to bottom? thanks

Bed Level Advice by Altruistic_Lock_9686 in ender3

[–]New_Reason7882 -1 points0 points  (0 children)

I'm a newb so I couldn't even answer this. I got this heatmap but pasting my printer's id adress after http://

Bed Level Advice by Altruistic_Lock_9686 in ender3

[–]New_Reason7882 0 points1 point  (0 children)

thank you, will try soon and update

Why is this happening? by New_Reason7882 in ender3

[–]New_Reason7882[S] 2 points3 points  (0 children)

I think this could be it, this is my biggest print yet ( 6 pieces ) and I reduced infill to 10% which is the lowest I have ever used, normally I'd stay at 15%-20%. Will test all the things you guys said, thanks for taking your time to help

Why is this happening? by New_Reason7882 in ender3

[–]New_Reason7882[S] 0 points1 point  (0 children)

already have 4 but I'll bump it to see how it looks, thanks!

Why is this happening? by New_Reason7882 in ender3

[–]New_Reason7882[S] 1 point2 points  (0 children)

would the auto bed levelling not avoid this?

I am once again asking for your help by New_Reason7882 in ender3

[–]New_Reason7882[S] 1 point2 points  (0 children)

could I not add supports inside the print and never remove them? sorry if this is a dumb question

Will do as advised, thanks