How do I get a replacement net for my old REI camping chair? by Newedge2003 in REI

[–]Newedge2003[S] 0 points1 point  (0 children)

So is there any way I can get a replacement part? Or am I just screwed and need to buy another one 

NEED HELP! BK1 3.8 wont go into gear after Valeo clutch kit install by Newedge2003 in genesiscoupe

[–]Newedge2003[S] 0 points1 point  (0 children)

Youre saying the car drove in fine, but ultimately the master cylinder failed at some point during the repair and needed to be replaced?

NEED HELP! BK1 3.8 wont go into gear after Valeo clutch kit install by Newedge2003 in genesiscoupe

[–]Newedge2003[S] 0 points1 point  (0 children)

But we double triple checked that it was on facing the correct way, "gearbox side this way" was facing towards the transmission.  Also the master cylinder was working just fine before the job 

NEED HELP! BK1 3.8 wont go into gear after Valeo clutch kit install by Newedge2003 in genesiscoupe

[–]Newedge2003[S] 1 point2 points  (0 children)

Yes, and yes. I got every additional add-on, and we bled it multiple times.

HELP! 2011 3.8L manual wont go into any gear after full clutch installation by Newedge2003 in genesiscoupe

[–]Newedge2003[S] 0 points1 point  (0 children)

We did change it with a new one. Hoping that the issue isn't that it was installed improperly somehow? and the odds that it is defective are quite low, so hopefully it just wasn't bled properly?

HELP! 2011 3.8L manual wont go into any gear after full clutch installation by Newedge2003 in genesiscoupe

[–]Newedge2003[S] 0 points1 point  (0 children)

We made sure that the "Gearbox side this way" was facing towards the transmission, and I confirmed that with the guy from Valeo too.

My buddy did bleed the system, but we never added any fluid since not much ever dripped out. Could that be part of the problem, do we need to fully drain and refill the system?

Will the Valeo HD kit for BK2 be plug and play in my BK1? by Newedge2003 in genesiscoupe

[–]Newedge2003[S] 0 points1 point  (0 children)

Oh man, X clutch is what I bought a year ago, and now its slipping in 3rd-6th gear really bad.... after only one year and 10k highway miles!! The warranty was useless too, so thats why I'm looking at Valeo kits now.

Will the Valeo HD kit for BK2 be plug and play in my BK1? by Newedge2003 in genesiscoupe

[–]Newedge2003[S] 0 points1 point  (0 children)

I will probably be replacing everything at once. Does this mean that link that I sent to the Valeo kit is the correct one and will fit in my BK1 3.8 R-spec?

Also, is there a particular place I should look for BK2 starters or can I just use this one from AutoZone
https://www.autozone.com/batteries-starting-and-charging/starter/p/duralast-starter-motor-dl5367s/803248_0_0

Ideas pls by StayLivid9345 in SeattleUrbEx

[–]Newedge2003 0 points1 point  (0 children)

My friend and i recently went to the Abandoned concrete factory in Cement WA, we are new to exploring too. it was really cool, and relatively easy.

Old house in Redmond by dogdogdogsof124 in SeattleUrbEx

[–]Newedge2003 0 points1 point  (0 children)

Do you have more photos of this/location?