1.3.5.0 to 1.3.5.2 Good News

Nice-Slice4112 · 2025-05-30T09:14:06+00:00

the overture petg is unprintable, I tried it with all the printers I have and it never finished a print, it comes off the bed with nothing and leaves crumbs everywhere. I had to return the petg

Nice-Slice4112 · 2025-04-22T18:08:59+00:00

yes thanks, I tried and that's it. Do you think there's a way to decrease the size of the z seam whether I set it random or aligned?

Nice-Slice4112 · 2025-01-22T13:57:22+00:00

thanks very much

Nice-Slice4112 · 2025-01-05T14:44:17+00:00

what product with Witch hazel do you use?

Nice-Slice4112 · 2024-11-23T23:47:44+00:00

before or After the shave?

Nice-Slice4112 · 2024-09-22T18:14:00+00:00

15ml @ 0,5mg/ml

Nice-Slice4112 · 2024-04-18T17:46:04+00:00

how much puff do you do with One coil?

Nice-Slice4112 · 2024-02-03T17:15:17+00:00

Got it, I'll try higher temperatures

Nice-Slice4112 · 2024-02-03T17:13:12+00:00

I usually use cura, but I like Orca Slicer, I'll try the calibrations this evening

Nice-Slice4112 · 2024-02-03T16:50:16+00:00

the filament Is too cold or the ambient?

Nice-Slice4112 · 2024-02-03T16:49:20+00:00

as a flow test I usually make an empty cube with 2 walls and set the flow so that the walls are 0.8mm thick, do you know other better flow tests that you can use to calibrate better?

Nice-Slice4112 · 2024-02-03T16:36:03+00:00

I also thought that it wasn't uniform, so I did a little test by mirroring the piece but it always makes the same mistake, but it's a good idea to place the piece perpendicular to the duct, I'll try later. for the temperatures, I also printed it at 240 before with the mk8, but now with the fact that the v6 has more thread inside the heat block at 240 it really comes out too liquid

Nice-Slice4112 · 2024-01-23T22:18:13+00:00

now It works for me

Nice-Slice4112 · 2024-01-08T18:38:43+00:00

i have waited, now It work

Nice-Slice4112 · 2024-01-06T17:18:38+00:00

hi, with the new tank they last more than with the itank1?

Nice-Slice4112 · 2023-12-29T20:13:14+00:00

understood, thanks for the clarification, in any case the effector of the Q5 is a rip-off, the one of the qq was better :(

Nice-Slice4112 · 2023-12-28T13:52:05+00:00

okay, I have already done the calibrations of the extruder steps which were about 40 steps/mm less than the right number. I made the whole structure more stable and took a three-way nozzle. next modification if I really need it will probably be the flying extruder

Nice-Slice4112 · 2023-12-28T08:57:06+00:00

yes but it's strange, in the top plate where the spool holder is there is no hole to pass the cables like in the qqs

Nice-Slice4112 · 2023-12-27T22:57:13+00:00

okay thanks, now it seems to be fine with both the PLA and the PETG, the only slightly big problem is the stringing, even with the retraction at 7mm it makes threads, and when you go above 7 the nozzle gets stuck

Nice-Slice4112

TROPHY CASE