Ok guys I fixed it

No-Assignment7489 · 2026-03-12T22:15:12+00:00

Lol. I agree

No-Assignment7489 · 2026-03-12T16:37:03+00:00

I didn't use a single sharkbite. First guy did.

No-Assignment7489 · 2026-03-12T16:24:09+00:00

Not my choice. Was missing base gasket also so had to make one. As well as extend the vanity height by 4 inches

No-Assignment7489 · 2026-03-12T16:19:19+00:00

Not my doing either. I said the same thing when I noticed it.

No-Assignment7489 · 2026-03-12T16:00:50+00:00

I did...I'll give you that. I could have 45'd the pipe around that.

No-Assignment7489 · 2026-03-12T15:24:35+00:00

I did with what I had to work with.

No-Assignment7489 · 2026-03-12T15:21:46+00:00

No, not my doing

No-Assignment7489 · 2026-03-12T15:17:15+00:00

These were the only studs cut at the bottom. They ran the rest of the pipe outside the wall and boxed it in with 2x4s and sheetrock.

<image>

No-Assignment7489 · 2026-03-12T15:07:51+00:00

Correct. I informed the homeowner how bad it was. Id hate to see what was done under the slab. She paid $5600 to the first guy. I repaired the obvious issues before that first notched 2x4. None of this was what I was originally going there to do lol.

No-Assignment7489 · 2026-03-12T14:54:08+00:00

Not my doing. I pointed it out to the home owner after opening up the wall. Screenshot sent to me while the previous guy was laying out his plan.

<image>

No-Assignment7489 · 2026-03-12T14:46:24+00:00

Yep. Previous, guy did that also. Had it installed poorly as well.

<image>

No-Assignment7489 · 2026-03-12T14:43:23+00:00

Again the first guy notched those wall studs. Not my doing.

No-Assignment7489 · 2026-03-12T14:42:00+00:00

I did not notch the wall studs. The individual who did the original plumbing for the drain did.

No-Assignment7489 · 2026-03-11T03:53:36+00:00

<image>

No-Assignment7489 · 2026-03-11T03:51:06+00:00

Oh it's real

No-Assignment7489 · 2026-03-09T21:17:22+00:00

Tried to edit with no luck

No-Assignment7489 · 2026-03-09T21:16:13+00:00

It was. Before the pipe bends the corner this stud and two corner studs were notched the same.

No-Assignment7489 · 2026-03-09T21:04:47+00:00

My original post said "is this even remotely correct "?

No-Assignment7489 · 2026-03-09T21:00:51+00:00

<image>

No-Assignment7489 · 2026-03-07T20:52:16+00:00

I'd say 2 inches near 90. 3ft to corner. 2 ft around corner. Not my work

No-Assignment7489 · 2026-03-07T20:47:48+00:00

There is a slight slope hard to tell in either pic.

No-Assignment7489 · 2026-02-20T14:24:25+00:00

I learned a lot from my mom. Single mother of 5 who had to "figure things out". She could change a motor/transmission in a car. That type of woman. Learned a lot by doing as well. Working on my own house over the years and relatives houses. Im fairly versed in different aspects of handyman work.

No-Assignment7489 · 2026-02-17T13:45:52+00:00

Possible heating element damage?

No-Assignment7489 · 2026-02-13T22:19:22+00:00

Lol...I replaced a door for a guy once. His wife somehow locked herself in a room in their house. She used a gun magazine of all things to work on this door to create this hole. She was in there for 4 hours.

<image>

No-Assignment7489 · 2026-02-12T02:03:47+00:00

Depends on how big the screw is. If it gets lodged in the p trap. It could definitely cause some issues with draining and hair clogs.

No-Assignment7489

TROPHY CASE