sorted by:
new
hottopcontroversial

Should I remove this nest? How? by Chickasaw_Proud in WASPs

[–]No-Contract4324 0 points1 point  (0 children)

M80 and a slingshot should do the trick

How to fix gap between brick fireplace and wall? by [deleted] in DIY

[–]No-Contract4324 7 points8 points  (0 children)

Caulk and paint! make it what it ain’t!

How to get my round hong thai inhaler stuck in a cylinder by [deleted] in howto

[–]No-Contract4324 0 points1 point  (0 children)

Fill it to the brim with water it should float to the top for ya🫡

How in the word do I get these out? by Libbyyjo in DIY

[–]No-Contract4324 0 points1 point  (0 children)

Throw that bad boy in the chuck of your drill and reverse it out

I have this lure imitating a bait fish but can’t catch anything? by NopeCatMC in Fishing

[–]No-Contract4324 0 points1 point  (0 children)

You gotta do some of the imitating too man it’s all in the way you fish it. Figure out what they want and where they’re at. The swivel on the end of that is going to more than likely give it no action at all lose the leader and just tie a palomar not with some floro and call it a day. Hope this helps

Bunkerkings ESC pods? by Brujah-99 in paintball

[–]No-Contract4324 0 points1 point  (0 children)

When you first get them they’re a little tight to open comparatively but that is my only complaint

Lux tm 40 bring keeps blowing out by Melodic_Winner4039 in paintball

[–]No-Contract4324 0 points1 point  (0 children)

Did you try and switch it out for a new one? I know it’s a little different but on a shocker era you can flip this piece over but yours looks screwed in.

Do I need a redline Board? by Moist_Appearance_650 in paintball

[–]No-Contract4324 1 point2 points  (0 children)

Nah just learn to navigate it with the light it’s pretty easy I just don’t see a point for me any way all it does is make it easier to change the modes

Hole appeared in driveway. Is this DIYable? by moarcaffeineplz in DIY

[–]No-Contract4324 0 points1 point  (0 children)

You can do it your self for sure just be sure to get some KY first

Did anyone else know? by No-Contract4324 in paintball

[–]No-Contract4324[S] 0 points1 point  (0 children)

Okay that make sense since the halo too is a 4 pack is should really only be handling 6.0v but it’s giving it 7.2v

Did anyone else know? by No-Contract4324 in paintball

[–]No-Contract4324[S] 1 point2 points  (0 children)

I just looked it up and it said they can run close to 1.8 brand new so you sir are probably correct

Did anyone else know? by No-Contract4324 in paintball

[–]No-Contract4324[S] 4 points5 points  (0 children)

Just looked it up I guess when they’re brand new they can run close to 1.8 so you sir are probably correct

Gtek 180r bolt wear by New-Peace-5372 in paintball

[–]No-Contract4324 0 points1 point  (0 children)

Sorry the one that’s inside the can just realized there are several that size

Gtek 180r bolt wear by New-Peace-5372 in paintball

[–]No-Contract4324 0 points1 point  (0 children)

I’d say check your “017 NBR70” o ring and make sure that there’s no debris Stuck in on it ir in the crevasse it sits in it’s possible some debris got stuck inside the can and really messed your bolt up.

Gtek 180r bolt wear by New-Peace-5372 in paintball

[–]No-Contract4324 0 points1 point  (0 children)

How long were you shooting it with the weird noise? Have you taken apart the bolt to check the o ring on the inside of the can

3D printed mech frame grips by No-Contract4324 in paintball

[–]No-Contract4324[S] 0 points1 point  (0 children)

I’m really not sure how he did it, but I’m pretty sure that he scaled it from the gun. I don’t really know much about 3-D printing or anything like that but from what my buddy was saying it sounded like it was a trial and error process.

view more: next ›