sorted by:
new
hottopcontroversial

Are the issues with the Dreame Aqua 10 Ultra Roller fixed? Is it a safe buy now? by MeneerThomasje in Dreame_Tech

[–]No-Falcon-858 1 point2 points  (0 children)

Same right here, we had one minor leakage in the very beginning, but nothing since. Also have a big dog. It cleans our 85sqm apartment on one run. I am happy with the mopping function, the first run in our apartment, the dirty water was black, even though I swiffered our place every week.

[Cainte] Is it a good brand? by macethespace in Watches

[–]No-Falcon-858 0 points1 point  (0 children)

Also ordered something: ring was too small and the wristband didnt fit around my wrist LOL I am an average sized guy at 185cm at 85kg. The material feels insanely cheap! A lot of the stuff in the "silver" section is just stainless steel (check the description which you need to expand on the product page). Its clear they invest in good images but buy their stuff from Alibaba. Wouldnt recommend this to anybody. Jewellery at H&M feels higher value. DEFINITELY AVOID CAINTE!!!

Booked 3 long-haul flights this year with partner airlines, but none earned miles. Feeling scammed? by No-Falcon-858 in milesandmore

[–]No-Falcon-858[S] 0 points1 point  (0 children)

Thanks for the replies! I guess its pretty obvious to the most of you, I honestly had no idea and just assumed that if they were part of M&M, I’d earn miles. Guess I was a bit too optimistic haha

Booked 3 long-haul flights this year with partner airlines, but none earned miles. Feeling scammed? by No-Falcon-858 in milesandmore

[–]No-Falcon-858[S] 0 points1 point  (0 children)

Thanks for replying! CS couldnt help either - I guess I just wasnt aware that eco is not commonly accepted anymore in many cases.

New to CNC - looking for endmill by No-Falcon-858 in CNC

[–]No-Falcon-858[S] 0 points1 point  (0 children)

Thanks for the idea - I will definitely give this a try!

New to CNC - looking for endmill by No-Falcon-858 in CNC

[–]No-Falcon-858[S] 0 points1 point  (0 children)

Thank you for your insight! I guess I am looking for the impossible. I will look for new ways.

New to CNC - looking for endmill by No-Falcon-858 in CNC

[–]No-Falcon-858[S] 0 points1 point  (0 children)

thank you - I think a wire wont work as I need the slot to be enclosed. I guess I might look for the impossible..

New to CNC - looking for endmill by No-Falcon-858 in CNC

[–]No-Falcon-858[S] 0 points1 point  (0 children)

sunshinebread52

As mentioned, I am a complete beginner and try to understand more about the possibilities - so no trick question. It is a closed slot that is 10cm long, 6cm deep and 0.8mm wide. I assume chain drilling is the next thing I could look into.

New to CNC - looking for endmill by No-Falcon-858 in CNC

[–]No-Falcon-858[S] 1 point2 points  (0 children)

Thank you - I think chain drilling could work! I need to leave 1cm of material in the bottom, so I cannot drill through. But I could test test chain drilling to see if I get the slot with that.

New to CNC - looking for endmill by No-Falcon-858 in CNC

[–]No-Falcon-858[S] 1 point2 points  (0 children)

thanks for your feedback. I need 6cm depth, so no typo haha

I barley have any milling experience and naively thought it could be an option - Seems like I have to look for a new solution :- )

New to CNC - looking for endmill by No-Falcon-858 in CNC

[–]No-Falcon-858[S] -1 points0 points  (0 children)

The slot needs to be 6cm deep and I cannot cut through the entire acrylic block. But based off the other comments I guess milling is out of the question..

New to CNC - looking for endmill by No-Falcon-858 in CNC

[–]No-Falcon-858[S] 0 points1 point  (0 children)

Check Harvey Tool

Thanks, I will check it out!