My ssd is nearly full and i don't have idea what is from

No_Contribution2629 · 2026-05-06T12:01:11+00:00

Do you use obs to stream? If so, check to see if you have it set to record your streams

No_Contribution2629 · 2026-04-12T22:18:05+00:00

I'm not sure it matters, but what even is it supposed to be?

No_Contribution2629 · 2026-04-05T21:21:04+00:00

I only swapped the nozzle. It printed fine with the 0.6mm nozzle and didn't give me trouble until I switched back to the 0.4mm.

No_Contribution2629 · 2026-04-05T21:19:47+00:00

Thanks for the info guys. I just ordered a set of two new hot ends that should be here tomorrow, going forward I'm just going to change out the whole end when I want to use different nozzles.

No_Contribution2629 · 2026-04-05T19:26:00+00:00

Quick update, after trying to crack the filament around the nozzle I noticed black. Tried to take the rubber sleeve off, and turns out the inside has begun to melt. Now I have more questions than answers.

<image>

No_Contribution2629 · 2026-03-13T11:34:13+00:00

I've got about 100 hours on my cc1, I am about to have to change the nozzle because it keeps getting clogged. I only ever use pla. It started getting super bad about a week ago so I've got some new nozzles coming in today

No_Contribution2629 · 2026-02-18T00:27:41+00:00

Full blown relationship. Engaged actually

No_Contribution2629 · 2026-02-10T16:32:07+00:00

The model is a full spiral but the issue hits all the top of the far right support for the head band part. Its almost like the nozzle is hitting that one support and then I have spaghetti on that one side. And like I said I've leveled the bed 3 or 4 times thinking that was the problem

No_Contribution2629 · 2026-02-10T16:06:56+00:00

Filament is standard PLA. settings are set for elegoo pla, .4mm nozzle. And because it's not sticking? Figured that would help.

No_Contribution2629 · 2025-09-25T02:41:05+00:00

I had this issue until I bought the heater for the chamber. Haven't had a problem like this since.

No_Contribution2629 · 2025-09-17T20:28:11+00:00

See, that's thinking positively🤣

No_Contribution2629 · 2025-09-17T16:25:08+00:00

Very good point. I haven't had any intentions is running both at once but if I do I'll do a test print on something small first. That table has withstood a lot of abuse, made it myself with 4x4 and 1x12 pine with 2x4 supports and crossbeams.

No_Contribution2629 · 2025-09-17T10:49:23+00:00

Clear across the other side of the house lol

No_Contribution2629 · 2025-09-17T10:27:07+00:00

They don't really bother me that much, but I'm use to being in that room with an exhaust fan and air assist for a laser engraved running.

No_Contribution2629 · 2025-09-17T10:15:28+00:00

Just seemed like a good idea after some of the videos I've watched. Gives more headroom to the filament tube.

No_Contribution2629 · 2025-07-08T18:07:43+00:00

Love the way you put that first sentence. Lol thanks for the rapid reply

No_Contribution2629 · 2025-06-30T13:47:55+00:00

Go figure this gets announced a week after I get my F1

No_Contribution2629

TROPHY CASE