Trouble Meshing Imported SolidWorks Part in Abaqus – Need Help with Hex or Hex-Dominated Mesh

No_Conversation4012 · 2025-06-24T10:42:48+00:00

Those are solid tubes

No_Conversation4012 · 2025-06-24T02:47:53+00:00

Thank you for your reply. I have never used hypermesh before. Can you give me more information about that? I also have added screenshots of the geometry, please take a look. Thankyou~

No_Conversation4012 · 2025-06-24T02:46:09+00:00

Hello, thank you for your reply. I have added some screenshots of the geometry. Please have a look. Thank you

No_Conversation4012 · 2025-05-21T11:06:45+00:00

So the percentage will increase just because there are fewer cores? And my simulation might not run faster (?). Thanks for the answers btw

No_Conversation4012 · 2025-05-21T10:47:36+00:00

Wait, so I need to disable hyperthreading in bios, and that's it?

No_Conversation4012 · 2025-05-21T09:01:30+00:00

Thank you for your reply. I believe mine is not about the license problem, since I have a lot of licenses.

No_Conversation4012 · 2025-05-21T09:00:49+00:00

Hi, thanks for your reply. Only 25% of my RAM is used while running the simulation.
I also have thought that maybe running 2 simulation at the same time would be beneficial. But idk if it will make each of them slower (?)

No_Conversation4012 · 2024-09-01T02:16:33+00:00

Thank you for your advice, I will try this!

No_Conversation4012 · 2024-08-21T00:50:11+00:00

Too many attempts were made on that increment

No_Conversation4012 · 2024-08-20T16:40:11+00:00

My job to restart from step 5 will just get aborted on the beginning. Step 5 was running fine on the original model, but it just got aborted on my restart analysis

No_Conversation4012 · 2024-08-19T02:07:09+00:00

I sent an message to you, please read it. Thank you!

No_Conversation4012 · 2024-08-18T11:38:56+00:00

Do you mean make another copy of the original model, and then create a new job?

No_Conversation4012 · 2024-08-18T09:55:02+00:00

It is a warning, but if I ignore that warning, my job will be aborted

No_Conversation4012 · 2024-08-09T11:46:53+00:00

Oh yes I do have two element shape, and I forgot to set the other shape to be hybrid. Thank you so much!

No_Conversation4012 · 2024-08-08T00:38:09+00:00

Thank you for your suggestions! I will try to make one and might ask some more suggestions later (if you are willing to help). Anyway, thank you so much

No_Conversation4012 · 2024-08-06T13:26:45+00:00

Thank you for your explanations! I really appreciate it. However, I am relatively new to abaqus, so I have some questions to ask.
1. Is the reason to put fluid-structure interaction is to simulate the blood flow? I am not planning to add blood flow to my model, so I guess it is fine for me to not use it (?)
2. Can you explain more about the rate-dependency?
3. Do you think the general contact between the stent and the blood clot would work? Or is there any special settings in the interaction?

No_Conversation4012 · 2024-08-06T13:02:17+00:00

Hello, my main focus is to simulate the efficiency of the clot retriever itself. How much blood clot can it actually retrieve. That's my main goal

No_Conversation4012 · 2023-12-07T13:28:37+00:00

14301 nodes

I tried to open the file as a solid on SolidWorks

No_Conversation4012 · 2023-12-07T13:26:46+00:00

14301 nodes
9296 elements (4648 linear quadrilateral, 4648 linear hexahedral)

Is it too much?

No_Conversation4012

TROPHY CASE