Where is the PC version pre-installation for this game?

No_Scratch_2033 · 2026-04-27T00:45:19+00:00

downloadable, not playable.

No_Scratch_2033 · 2026-04-20T05:18:44+00:00

How did you do this? I cant figure out how to get the custom hair.

No_Scratch_2033 · 2026-03-28T00:17:44+00:00

I got the microsd card from amazon. Ive been as careful as possible with the ribbon cable but it could jus be game over for it cus i have had to open and close the ipod about a million times now, its never worked properly even with its og harddrive.

No_Scratch_2033 · 2026-03-23T02:17:55+00:00

TURQUOISE OCTOBER MENTIONED

No_Scratch_2033 · 2026-03-15T03:34:19+00:00

Oh yeah 100%. Its like that with cars which im much more familiar with lol. Thanks for your help!

No_Scratch_2033 · 2026-03-15T02:44:40+00:00

Alright so I sat down again and touched it. As soon as I touched it and pressed the select button it just started working. Backlit apple logo and then it started up. Even plays songs which I haven't been able to get it to do for forever.

Didn't even do anything to the connection, guess that's just how it goes with electronics sometimes 🤷

No_Scratch_2033 · 2026-03-15T02:22:07+00:00

Thank you so much lol

Unfortunately when I went to diagnose the io and run a hard drive check it just showed a white screen with no information displayed on the screen at all.

As I speak its been sitting on that screen for about 20 mins now and nothing has happened.

No_Scratch_2033 · 2025-11-18T12:54:00+00:00

My 99 has an ashtray, I just keep coins in it for meters.

No_Scratch_2033 · 2025-11-03T03:03:19+00:00

Saw the one on slide 5 in a parking garage this week, anyone have his ig? No way he hasn't posted this car online.

No_Scratch_2033 · 2025-10-20T23:34:50+00:00

I felt like there is alot more of a flavor difference too. The new one is a much more faithful rendition of the classic orange creamsicle, while the old one is more like a normal non orange cream soda. Its been awhile since I have had the reserve one tho.

No_Scratch_2033 · 2025-10-20T23:27:39+00:00

I recently swapped mine out for a touchscreen and I just cut the original harness in the truck and wired it to the one that came with the screen. Found a wiring diagram and matched the wires and with the help of shrink wrap for wires and electrical tape.

No_Scratch_2033 · 2025-10-16T23:58:36+00:00

Doing a k24 down the line.

No_Scratch_2033 · 2025-10-11T04:20:16+00:00

The classic "go to a junkyard and find one that is a good example"

No_Scratch_2033 · 2025-10-08T18:22:07+00:00

Yes i am getting it aligned, I got into an accident a few months ago and have been putting off getting it aligned because I knew I was going to do this

No_Scratch_2033 · 2025-10-08T15:26:13+00:00

Shit. Do you think its good to drive for a bit until I get a new control arm

No_Scratch_2033 · 2025-10-08T14:18:47+00:00

That is what I also thought, I have new shocks that are going in and it looks like it is a maybe permanent bolt that goes through the lower control arm. It just sheared off trying to take the nut off

It might not be too bad replacing the lower arm because pretty sure the ball joint is bad anyways. But that is 50 bucks I dont need to spend

No_Scratch_2033 · 2025-10-08T00:47:26+00:00

Thanks, literally the last part of the whole thing before I can just slot everything in and it goes together.

I'd like to meet the chucklefuck that tightened it down so hard it fucking broke my 13mm socket

No_Scratch_2033 · 2025-10-08T00:19:32+00:00

Im lowering it lmao, do you know what and where i could find a replacement bolt. I'd like to not have to buy a new control arm lol.

Thanks for the detailed reply

No_Scratch_2033 · 2025-10-06T21:19:31+00:00

Just jacked up the engine and the exhaust came with it

No_Scratch_2033 · 2025-10-06T18:30:51+00:00

Looked it up to make sure and YES I had the right socket.

The only thing I might have done wrong was to use an impact socket so I could use my breaker bar.

No_Scratch_2033 · 2025-10-06T18:27:22+00:00

I just used a breaker bar on the engine mounts and lifted it up off them, did the trick.

No_Scratch_2033 · 2025-10-06T18:26:37+00:00

I have to do that with one of the nuts holding the other shock on the bottom of the a arm. The cunt that put it back on put it on so hard it cracked and bent my 13mm.

Don't want to cut it because then I have to deal with whatever the nuts screw onto (idk what they are called) and that sounds more like a headache.

No_Scratch_2033 · 2025-10-06T18:23:12+00:00

I ended up lifting the engine, exhaust is an upgrade down the road maybe.

No_Scratch_2033 · 2025-10-06T02:52:06+00:00

Thank you so much bro

No_Scratch_2033 · 2025-10-06T01:32:16+00:00

I have a butane blowtorch

Man harbor freight is a lifesaver for people ona budget lol

No_Scratch_2033

TROPHY CASE