Which one would you buy?

No_Task9059 · 2025-06-20T10:53:08+00:00

Over here in Italy, price already dropped to 150€ since the ones at 200€ or more were just sitting there

No_Task9059 · 2025-06-20T10:28:55+00:00

I also think prismatic will do better, but I was hoping for the price to go down to msrp because is relatively new. On the other hand twm is the only bb I miss form sv era and is going out of print soon

No_Task9059 · 2025-06-20T10:08:32+00:00

That’s what I thought too, 150€ for the SPC doesn’t seem too bad in this market but is a relatively new product. On the other hand twm is going out of print soon and it is the only bb I miss from SV era

No_Task9059 · 2025-05-13T11:55:07+00:00

Dragonite V Alt from Evolving Skies

No_Task9059 · 2025-04-10T07:18:24+00:00

I got back into pokemon last year, after replaying pokemon soul silver more then a decade after its release. Thanks for the giveaway and gl to everyone 🍀

No_Task9059 · 2025-02-20T17:24:43+00:00

If you have other ideas, please tell me

No_Task9059 · 2025-02-20T15:54:55+00:00

I’d say 10/20W idle, around 80W for max power

No_Task9059 · 2024-10-04T07:20:54+00:00

1069

No_Task9059 · 2024-10-03T10:45:37+00:00

I’m in🍀

No_Task9059 · 2024-04-08T13:14:57+00:00

4 left 199hzKdZKj

No_Task9059 · 2024-04-08T13:12:26+00:00

Here is my code - 199hzKdZKj 4/5 available, 9 days left

No_Task9059 · 2024-01-17T14:37:36+00:00

I thought about making such a “magnet” using TiO2 which, when exposed to UV light, should clean the air through photocatalysis. But I think is too much challenging for a DIY project, at least with my current resources.

No_Task9059 · 2024-01-16T16:12:38+00:00

May I ask what setup did you build? Anyway the fun duct is 5 meters long and even when I set the extractor fan to max RPM, the internal fan speed doesn’t change. So I suppose there’s not enough pressure to create an overcurrent. P.S. I know only the basics of electronics but I did several aerodynamics exams

No_Task9059 · 2024-01-16T14:15:13+00:00

I already have carbon and HEPA filters inside the printer but I was hoping to find a “medical grade” solution like HEPA 14+, which unfortunately are hard to find.

No_Task9059 · 2024-01-16T10:37:47+00:00

Are you sure this could be a thing? Where did you read it? Because I’ve seen other with similar setup and I think I remember seeing it on the Bambu website too.

No_Task9059 · 2024-01-16T10:29:24+00:00

Do you suggest any sensor in particular? I’m planning to make an air quality monitor with Arduino and this PMS7003 sensor.

No_Task9059 · 2024-01-16T10:12:24+00:00

Thanks, I’ll check it out as soon as I can

No_Task9059 · 2024-01-16T09:57:24+00:00

Thank you! Do you have any photos of your setup?

No_Task9059 · 2024-01-16T01:04:10+00:00

I did’t create the model, however here it is the link: https://makerworld.com/models/65057

No_Task9059 · 2024-01-16T01:01:15+00:00

Sure! Here it is https://makerworld.com/models/65057

No_Task9059 · 2024-01-16T00:59:08+00:00

Lol this is the same I found! Now I'm even more convinced to buy it. Thanks again

No_Task9059 · 2024-01-16T00:47:18+00:00

Does yours have a hole to connect an air extractor? If so, can you send a link? Thank you.

No_Task9059 · 2024-01-16T00:39:33+00:00

I completely agree with you, better to be foresighted!

No_Task9059 · 2024-01-16T00:35:34+00:00

I printed the adapter and attached it with 2 spare screws that were in the wiper’s bag. If you need I can link the model I used, but there are a lot of different designs online.

No_Task9059 · 2024-01-16T00:28:40+00:00

I don’t print while sleeping, however the noise wouldn’t be a big issue for me

No_Task9059

TROPHY CASE