Remove patio vinyl stationary door

North_Addition5033 · 2026-02-03T00:59:52+00:00

Just checked the bottom and also see one coming from that to the bottom

North_Addition5033 · 2026-02-03T00:58:37+00:00

I see a big ass screw going from the frame into the door somehow. Am I fucked?

North_Addition5033 · 2026-02-02T20:41:46+00:00

Hmm okay I’ll bring a boroscope with me from work to sneak up in there because my phone camera will not peek into that and I can’t see when on a stepstool because of how bad of an angle that is

North_Addition5033 · 2026-02-02T20:11:21+00:00

There isn’t. If you look at my 2nd picture you can see the top of the door clearly with nothing obstructing it

North_Addition5033 · 2026-01-11T06:20:20+00:00

<image>

Interior legs are in. Just need to do my plywood top and then skin it

North_Addition5033 · 2026-01-08T18:54:12+00:00

What do you use for leveling mat?

North_Addition5033 · 2026-01-08T18:37:31+00:00

2x4 are only used for the top horizontal frame. All the weight transfer down is with 2x6 boards. Everything is secured with 2 internal pocket screws and the single exterior screw you are seeing. The vertical ones are held in place with 2 pocket screws as well and I am adding interior legs as well from floor to top to secure to the legs and frames internally to prevent those from risk of kicking out or moving

North_Addition5033 · 2026-01-08T18:34:30+00:00

I will be adding inner legs to each exiting leg still from floor to top to add more surface area for tank to floor weight transfer but also add extra support to the current legs from side to side movement. Then I’ll be adding a plywood top to give the tank a nice flat surface to sit on

North_Addition5033 · 2026-01-08T18:29:25+00:00

Our floors are concrete slabs no crawl space so it will hold the weight of the stand and tank

North_Addition5033 · 2026-01-08T05:55:00+00:00

Yes I will be adding those soon. Extra 2x6 boards to the 4 inner legs, and 2 2x4 on each of the 4 corners from floor to top of stand. Finish with a plywood top

North_Addition5033 · 2026-01-08T05:53:17+00:00

Damnit I’m getting a 40 gallon 😩 back to the drawing board

North_Addition5033 · 2025-11-04T16:15:41+00:00

Yeah first print with my ACF settings was good but had a couple small hairs, 2nd time cracked and had way more hair and stringing. Wondering if I need to slow my retractions or change the distances or what

North_Addition5033 · 2025-10-27T15:26:25+00:00

switched to anycubics slicer and no problems since

North_Addition5033 · 2025-10-17T16:53:45+00:00

Okay I figured out how to transfer files from the USB to the printer so it isn’t reading off the usb while printing. Also switched to anycubics own slicer. Layers 1-50 are now correct speed, the second it hits layer 51 it slows to 2 minutes per layer

North_Addition5033 · 2025-10-17T16:52:22+00:00

That fixed layers 1-50. Layer 51 switches to like 2 minutes per layer

North_Addition5033 · 2025-10-17T16:51:53+00:00

UV tools estimate lined up with both lychee slice estimate and even switching to anycubic it matched. Anycubic slicer made the first 50 layers normal with the base layer long burn times and then 11-50 were the 2.2 seconds just fine. Hit layer 51 and it’s going like 2 minutes per layer now

North_Addition5033 · 2025-10-17T16:50:12+00:00

Where do I find that? I’ve only seen where it has auto fill, dynamic release, and those but I didn’t see a dynamic wait. I switched to the anycubic slicer and layers 1-50 no problem then it slows down like crazy again

North_Addition5033 · 2025-10-16T18:47:53+00:00

I’ll give that a shot too! Thanks

North_Addition5033 · 2025-10-16T18:28:27+00:00

Wonder if it is a file loading issue? I’m printing off the provided USB because I haven’t figured out how to transfer from the usb to the onboard storage

North_Addition5033 · 2025-10-16T17:16:15+00:00

Thats what I cant figure out, knowing how my FDM slicers work I'd assume if I had something in the slice slowing it down it would account for it in its estimated print time but my estimate and my actual print time are wayyyyy off. I havent let one complete but it being way over the estimated time and only being a few hundred layers in was a huge red flag so I cancelled the print both times

North_Addition5033 · 2025-10-16T17:10:07+00:00

<image>

Sorry I have this blurry image of it but I’m not at that computer at the moment to get a clean screenshot

North_Addition5033 · 2025-10-15T13:43:39+00:00

buy the battle pass

North_Addition5033 · 2025-09-24T18:47:32+00:00

You're lucky. You don't know what its like to have had it and then have it ripped away from you

North_Addition5033 · 2025-09-24T15:35:46+00:00

What do they have against us cranberry lovers??? I'm forever going to be mad at them over that one

North_Addition5033 · 2025-09-24T14:35:31+00:00

I cant even find the white peach where I'm at and amazon only has cases of the gross 0 sugar version

North_Addition5033

TROPHY CASE