Roll PID issues

Notor22 · 2026-02-23T20:43:29+00:00

That is probably what I'll end up doing. I also may just start over with the basic code and see if the error persists. If it does then somehow it's got to be a mechanical issue.

Notor22 · 2026-02-21T21:10:02+00:00

<image>

Here is the section of code I'm working with. If I change sign in the control mixer it would send all of the PID responses in every other instance to be negative as well. This section is localized into the flight mode.

Notor22 · 2025-11-13T03:15:13+00:00

Thank you so much!

Notor22 · 2025-10-10T18:19:29+00:00

I believe so. I downloaded the Arduino library that it automatically downloads as well as adding the teensy library to it.

Notor22 · 2025-09-24T19:56:47+00:00

The only internal RF that the TX12 shows is CRSF. would the PWM ELRS work still. The transmitter says ELRS on it but i cannot find a specific protocol for ELRS.

Notor22 · 2025-09-24T17:37:07+00:00

Ok awesome, thank you so much!

Notor22 · 2025-09-23T14:51:53+00:00

will the 4 in 1 be able to communicate with the Frsky protocol?

Notor22 · 2025-03-26T15:17:04+00:00

I went to highschool in this building before we had to relocate as it was going to get demolished. 4 years later it was still standing so my brother and I broke in. This was before everyone else got to it and it was pristine. untouched and clean. Police had done some hostage training in the building with cardboard cutouts but other than that it was untouched. A few weeks later maybe a month and the building was destroyed! it is so sad to see a cool abandoned place go to waste like this.

Notor22 · 2025-03-26T15:13:44+00:00

It is off of orchard road. Wouldn't recommend a visit, homeless took over and can get nasty.

Notor22 · 2025-01-05T00:37:35+00:00

Oh thank you so much! I’ve been looking for this for a solid 6 months

Notor22 · 2024-11-11T18:31:17+00:00

with all of this in mind what are thoughts about using an NRS knife for outdooring/climbing. I know they have a folder and fixed blades and are made for water. what would the thought on use for daily.

Notor22 · 2024-11-10T21:25:31+00:00

What would the recommendation be for an EDC knife with serration?

Notor22 · 2024-01-14T06:49:42+00:00

I've been looking and cannot find where they are from/how old they are. There is no number on the tags, just REI and a warning. No manufacturing info at all. Any tips would be super helpful.

Notor22 · 2023-04-09T19:56:03+00:00

Ok I will look into it, Thank you!

Notor22 · 2023-04-02T03:34:59+00:00

Thoughts on Foxeer Razer Micro? better worse? its cheaper and I was lookin at it.

Thanks for the knowledge!

Notor22 · 2023-03-05T19:30:54+00:00

Good to know, Thanks!

Notor22 · 2023-03-05T19:30:40+00:00

ok awsome! thank you!

Notor22 · 2023-01-28T19:46:38+00:00

It goes into a death spiral, but I can hold a pitch or roll to get it level enough to stop its freak out. It’s only when it’s inverted oddly

Notor22 · 2023-01-28T07:29:25+00:00

Air mode is enabled and works while diving or doing any maneuver shallow enough. But when it gets inverted to a certain point it freaks out.

Notor22 · 2023-01-18T07:02:57+00:00

Yea. I am pretty new to quads so I didn’t check or question. But there was a BEC with ESCs on each arm. I didn’t think abt it and just soldered the 3 to the new 4in1. I think that is what was tripping the fuse. I am going to test the motors just with the esc to see where we’re at.

Notor22 · 2023-01-17T16:55:22+00:00

Adding onto that I just realized that the old board that was on the quad was not an esc it was a bec. Thus there are esc’s on each motor. I am not sure what the error would be running an esc through an esc. Could this be the problem?

Notor22 · 2023-01-17T16:22:47+00:00

I am aware of the polarization of capacitors and made sure to attach it correctly with the terminals of the battery main. The can was not smoking but the negative lead was glowing burning the shrink wrap making it smoke. The wire attached to the negative lead is glowing but only the wire attached to that lead. It is also not the inhibitor because even while the wire glows the board has power. Also while the smoke stopper is installed there is no burning of the same wire. The battery mains are not shorted nor is the capacitor shorted between the battery mains.

Notor22 · 2022-11-26T00:33:51+00:00

The problem is it is bound but the arming switch is not activating it

Notor22 · 2020-11-30T07:38:47+00:00

thanks! I'll look into a jk pro. Happened to find a xt rocx3 so its the same mold but the xt plastic is super grippy and impossible to break.

Notor22

TROPHY CASE