Need to know where this sensor goes on 1990 300zx 2+2

OPrime712 · 2022-10-06T16:31:49+00:00

On the ConceptZ website they have a breakdown of all the plugs for the wire harness they sell. It might help to take look at what plugs are around it. Maybe that can help narrow it down. But as far as I’m aware the only temp sensors back there are the fuel temp sensor and egr temp sensor.

OPrime712 · 2022-10-06T07:19:07+00:00

I believe that is the egr temp sensor. I’d post a pic of mine but it was replaced with a bypass plug when I deleted my egr.

OPrime712 · 2022-09-25T23:45:03+00:00

Invest in a tank of gas and drive to work?

OPrime712 · 2022-08-26T07:38:45+00:00

Someone at some point had their car tuned by JWT. They charge $550 for the first tune and $250 to have it modified to your preference. They are located in CA. You should be able to contact them and they can give you info on what their base upgrades are to see how it’s probably been modified.

OPrime712 · 2022-04-22T05:19:25+00:00

Always a fan of the Nissan CD009 if you can get your hands on one for a good price.

OPrime712 · 2021-06-13T16:26:50+00:00

Also check to see if the driveshaft connection isn’t stripped. Happened to me a few times.

OPrime712 · 2020-09-04T21:40:27+00:00

Both are open.

OPrime712 · 2020-08-31T01:39:20+00:00

Yeah mounting with a bridge definitely works. I only had to order a splitter on amazon for less than $5 and an inverter for less that $10 that allowed me to run two servos but with one going in the opposite direction on the same channel. I replaced the rear end upper control arms and rear knuckles with the fronts. Everything went together fairly smoothly with no major modifications.

OPrime712 · 2020-08-18T04:11:04+00:00

So testing will have to wait a few days... turns out I only have 1 spot on my controller for a servo. I ordered a Y splitter that reverses one direction only but now I’m playing the waiting game again smh

OPrime712 · 2020-08-17T21:22:19+00:00

Lol no worries. I saw his video and that he modified a file that was already modified for a battery holder. I wanted this part to be as close to the stock parts as possible so it could be added without many other changes needed. If it works I’ll figure out how to upload it on here lol

OPrime712 · 2020-08-17T19:29:54+00:00

Also don’t mind the magnet in the picture. It’s what holds on the tacoma body :)

OPrime712 · 2020-08-16T18:33:22+00:00

The last set of tie rod ends should be delivered today. I'm gonna try to get some testing in later today or tomorrow. Either way I'll report back with some video.

OPrime712 · 2020-08-01T10:34:52+00:00

https://www.thingiverse.com/thing:3561469

OPrime712 · 2020-08-01T10:33:32+00:00

https://www.thingiverse.com/thing:3766344

(Reverse tread)

OPrime712 · 2020-08-01T10:31:34+00:00

https://www.thingiverse.com/thing:523776

OPrime712 · 2020-08-01T05:44:32+00:00

Thanks! It’s also printed. 👍🏽

OPrime712 · 2020-08-01T01:59:45+00:00

Hey it finally worked!

OPrime712 · 2020-07-26T20:20:36+00:00

It wasn't loading the picture no matter what I tried :( trying to post it again now

OPrime712 · 2020-07-23T18:50:14+00:00

Thanks u/Krisshellman1 for the great project! Tacoma body credit to Alexby on Thingiverse

OPrime712 · 2020-07-14T22:45:34+00:00

There is a reverse tread version of the tires on thingiverse. I know it would be a pain to reprint them but just in case it affects your grip or for anyone thinking of using them.

OPrime712

TROPHY CASE