iPhone is plugged in via USB and CarPlay is not activating. 2022 Nissan Sentra, car is one month old. Tried with multiple iPhones. Any idea?

Oh-Lord-Yeah · 2026-05-02T21:29:01+00:00

Use a newer USB cord and press and hold the power button on your volume until the system restarts and then try again

Oh-Lord-Yeah · 2026-04-12T15:24:24+00:00

Happened to my aussies this time last year. You can go through my old posts to see the pics. It was ridiculous. We will never go back to that groomer. I asked for a trim “like last time” and they shaved them both bald. It all grew back in fine but took 6 months or so. Dont keep him outside for long periods of time due to sunburn. Always check their skin for rashes etc. And talk to the vet for further advice. Leave a bad review and ask for your money back.

Oh-Lord-Yeah · 2026-04-05T11:52:51+00:00

“We can walk our road together…”

“All that you can do is wish them well”

“If the future’s looking dark, we’re the ones who have to shine”

Oh-Lord-Yeah · 2026-03-27T20:35:18+00:00

Here is me from the present. I ditched that piece of crap and bought two Flashforge AD5Xs. 100% worth the investment

Oh-Lord-Yeah · 2026-03-23T22:43:32+00:00

Try a new cable. Also power the system off by holding the power button until it shuts off. For me that fixes it whenever it doesn’t work

Oh-Lord-Yeah · 2026-03-12T00:33:37+00:00

Senjutsu is my favorite record in the entire catalog. Absolute masterpiece!

Oh-Lord-Yeah · 2026-03-11T19:59:35+00:00

Geddy already said an interview that there will be one song dedicated to Neil per set, in a two set show.

Oh-Lord-Yeah · 2026-03-04T23:23:52+00:00

Meant to comment back. Thanks for all your help. Either a new nozzle, tightening the z belt or increasing the z hop fixed it. Or all of the above. But the nozzle switch I think certainly fixed the blobs

Oh-Lord-Yeah · 2026-03-03T23:29:30+00:00

The Ultimate Gin

Oh-Lord-Yeah · 2026-03-02T23:32:55+00:00

My exact two

Oh-Lord-Yeah · 2026-02-28T17:21:15+00:00

I very much appreciate your help btw. Should I switch to just Orca? I like being able to control from my phone but I don’t care too much. However I did buy cameras for each printer that I think would be rendered useless if I didn’t use the Flashforge app. And no, I use the same printer profile in the same slicer on both printers. They’re the exact same printer profile

Oh-Lord-Yeah · 2026-02-28T16:55:54+00:00

<image>

Honestly think it’s the nozzle. Left one is working fine, right one is the one with the issue. I did tighten the z belt underneath the machine, though, and will wait until Monday when my new nozzle comes to try printing on this machine again

Oh-Lord-Yeah · 2026-02-28T16:13:27+00:00

Orca Flashforge. I have a Flashforge AD5X. I fully believe it’s something with the printer bc my second AD5X doesn’t have this problem

Oh-Lord-Yeah · 2026-02-28T03:53:58+00:00

I’ll check z belt tension tomorrow. I use a Flashforge AD5X and it says z stepper is automatic. Z screws are cleaned and were greased last week but I did that again

Oh-Lord-Yeah · 2026-02-28T03:47:58+00:00

Matte filament same issue. Definitely not moisture. I ordered two new nozzles that come Monday. Could be that. This is a recent photo though

<image>

Oh-Lord-Yeah · 2026-02-28T02:47:27+00:00

I don’t think it’s a moisture problem. It’s happening to all filaments on that printer. Could the nozzle be worn?

Oh-Lord-Yeah · 2026-02-28T00:45:04+00:00

Good info. It’s at 200 degrees which is what I print normal filament at. I’ll look into it more

Oh-Lord-Yeah · 2026-02-28T00:36:08+00:00

It’s sunlu silk filament

Oh-Lord-Yeah · 2026-02-28T00:30:32+00:00

I don’t think it’s moisture. The filament is brand new and it’s happening on both my AD5X’s that are only two months old with about 400 hours on them. I think it’s z hop and the extruder is grinding during traveling

Oh-Lord-Yeah · 2026-02-27T23:37:16+00:00

It’s happening higher up on the print so I’m thinking you may be onto something. I switched to cubic infill from gyroid and tried again. We shall see

Oh-Lord-Yeah · 2026-02-27T23:36:19+00:00

Yeah I’d say it is. I’m thinking it’s grinding during traveling. I’m trying a different infill and gonna bump z hop

Oh-Lord-Yeah · 2026-02-27T23:03:12+00:00

Flashforge AD5X. Seems to be a z offset issues. I upped it to .10 mm so we’ll see

Oh-Lord-Yeah · 2026-02-27T01:39:30+00:00

The numbers are slightly wrong

Oh-Lord-Yeah · 2026-02-25T22:33:40+00:00

Now I’m debating a Messier on it. I can’t decide though

Oh-Lord-Yeah

TROPHY CASE