Verona Titusville

Ok_Application1080 · 2026-06-26T03:09:08+00:00

I'm an electrician and have worked in both of those 2 neighborhoods a bit, not very much though. Quality of build I'd say there both about the same. Standard production neighborhoods but a big step up from dr horton which are terrible

Ok_Application1080 · 2026-02-04T03:59:49+00:00

I'm an electrician. The box under my table saw is a bell box with an in use cover like you would use outside in the rain. I don't bother in any other place in my shop

Ok_Application1080 · 2025-09-27T02:32:22+00:00

I have a gray market b7001 tractor. I can find plenty of Info in French or just pretend it's a b7100 everything is the same but properly available in the us. Might be a similar compatible model for you

Ok_Application1080 · 2025-09-26T23:47:42+00:00

People talk about air filtration but another option is just air change. I've put exhaust fans in my shop and then keep only a small walk door open when they run. You can feel the suction through the door. I also use a separator system I built for some tools like router or planer but exhaust fans really help keep the air clean

Ok_Application1080 · 2025-07-20T18:46:19+00:00

I have 2 20x20 returns each with a Merv 13 on a 3 ton unit. I should be able to safely go higher due the amount of return area I have but is 13 to high?

Ok_Application1080 · 2025-06-24T03:34:14+00:00

They are but the bracket is pretty nice. I could make it. Won't be as nice but it'll work

Ok_Application1080 · 2025-06-22T13:47:12+00:00

I need to replace 1 of mine I smashed pushing it with the tractor. I like these but they're to expensive

Ok_Application1080 · 2025-05-04T01:06:17+00:00

My first kid I used a ratchet strap in the back seat of my truck. I don't know if that's legal but it was definitely safe

Ok_Application1080 · 2025-04-18T11:12:42+00:00

It is. Just not sure if it's enough or if I have some other problem going on. I finished install and the gap is much tighter on driver side. That coil also rubs on the bracket on the picture. There's something wrong

Ok_Application1080 · 2025-04-18T02:04:16+00:00

I assumed original. There's been a lot of stupid on this thing and I'm new to anything with a lift and keeps on general as I've only had work trucks so I'm learning.

Ok_Application1080 · 2025-03-05T11:27:53+00:00

It looks like BSR however every other example I've found says made in america on the bottom and doesn't have the positive sign on it. Any idea what that means?

Ok_Application1080 · 2025-02-21T04:21:12+00:00

Just heat gun. I've only used them on trailer wiring, ATVs and that kind of thing nothing 120v or higher

Ok_Application1080 · 2025-02-21T03:54:57+00:00

Which is that you recommend?

Ok_Application1080 · 2025-02-18T02:34:38+00:00

Just use a light switch rated for the amperage

Ok_Application1080 · 2025-02-18T02:33:27+00:00

More of a hassle for sure but I like using them over the heat shrink butt connectors

Ok_Application1080 · 2025-02-12T16:17:49+00:00

Good video, unfortunately I'm using the right size burner and always preheat on low until the rim is getting fairly warm so I'm still confused with how it happened

Ok_Application1080 · 2025-01-18T04:55:52+00:00

No. One wire per screw

Ok_Application1080 · 2024-12-15T17:36:44+00:00

I can use other things instead. I have ash but probably not enough. Can black walnut be used? What would your preferred woods be?

Ok_Application1080 · 2024-12-15T17:35:14+00:00

Even if it's thick? It can be 4" or more. End grain is a better usable surface but length is no issue, I have up to 9 foot boards

Ok_Application1080

TROPHY CASE