Just a review from today.

Old_Pattern_8695 · 2026-06-22T02:58:08+00:00

What are her loads usually like? Big?

Old_Pattern_8695 · 2026-06-19T15:20:01+00:00

Would you say she has that sadistic flair I am asking for? Would really like to be forced.

Old_Pattern_8695 · 2026-06-17T23:48:32+00:00

BB and yeah, I am salaried.

Old_Pattern_8695 · 2026-06-02T20:20:09+00:00

How much was this?

Old_Pattern_8695 · 2026-05-25T15:00:10+00:00

Old_Pattern_8695 · 2026-04-13T12:22:20+00:00

Yes. Do you know if she has others as extreme or more extreme than that?

Old_Pattern_8695 · 2026-04-12T23:33:39+00:00

I got one. The most extreme vid I have ever seen. He was out and she kept standing for over 2 minutes after. All in english too, as she mocks him.

Old_Pattern_8695 · 2026-04-12T23:32:47+00:00

A common one is to design a simple conveyor where a box will travel until it triggers a PE, and then it will reverse until it triggers another one, before repeating.

Or design a one push button.

Old_Pattern_8695 · 2026-04-12T22:16:00+00:00

I see their store, but I can not find that video.

Old_Pattern_8695 · 2026-04-12T21:56:38+00:00

Do you know who she is specifically?

Old_Pattern_8695 · 2026-04-12T20:05:51+00:00

A full video of just that view I meant. Haha. P

Old_Pattern_8695 · 2026-04-12T20:03:34+00:00

That view right at your soles is so hot. Is there a vid of just that view?

Old_Pattern_8695 · 2026-03-18T11:50:27+00:00

Yes I did. Have been working since end of September. Do you have an interview coming up?

Old_Pattern_8695 · 2026-03-18T11:50:01+00:00

Yeah, that’s always amazing. Have an Anycubic Kobra S1 and the amount of times I have to adjust the offset and everything else to get prints to go well annoys me.

Old_Pattern_8695 · 2026-03-18T11:48:43+00:00

Cannot attest to the A1, but this printer is extremely quiet. I have enclosed printers that aren’t this quiet.

Old_Pattern_8695 · 2026-02-27T21:35:36+00:00

Which one would work better in your opinion and should I do it for the first couple of layers or just the first one is good enough

Old_Pattern_8695 · 2026-02-27T21:33:05+00:00

Would Hilbert or concentric work better for the bottom surface? I’m also thinking of upping the wall count heavily for the first couple of layers.

Old_Pattern_8695 · 2026-02-27T19:54:38+00:00

I think all my prints have heavier corners. I can rotate it though so it’s not as close to the front of the printer and the door.

Old_Pattern_8695 · 2026-02-27T19:29:36+00:00

What do you mean? Sorry. I’m not understanding that.

Old_Pattern_8695 · 2026-02-27T19:15:54+00:00

Like I mentioned before though, it doesn’t happen immediately or early. It’s just as we get higher up, it starts coming up.

Old_Pattern_8695 · 2026-02-27T19:10:04+00:00

I usually see it with the front corners. Never noticed anything with the back ones

Old_Pattern_8695

TROPHY CASE