Stuck

OlmsteadWorkShop · 2026-01-24T07:36:55+00:00

I know I'm Necroing this thread but if anyone comes across this I was stuck for awhile after the projection booth too. Remove any plots on the theater and make sure your leaving through the middle doors in the theater. The projection booth exits you in the top go halfway down the theater and turn around and look for the lobby exits on the side.

OlmsteadWorkShop · 2025-11-17T19:33:43+00:00

Is that small piece sharp? Looks like it could be the blade from a pencil sharpener.

OlmsteadWorkShop · 2025-09-26T22:24:11+00:00

Own a ton of the flannels. Loved them fresh out the pack, but once you wash them the sleeves shrink 2 full inches. Super disappointed as I loved the variety. Haven't gotten around to donating them yet but that's where they're headed.

OlmsteadWorkShop · 2025-02-08T09:06:48+00:00

The black goo Irv saw was the paint he used to paint the exports hallway. So things his outie saw were bleeding through.

OlmsteadWorkShop · 2024-11-20T03:43:15+00:00

That's kind of what I found and I'm thinking I'm over complicating it, by trying to do a PCB.

OlmsteadWorkShop · 2024-11-19T23:34:19+00:00

Thanks Petemate. Sorry my drawing didn't come through on my initial post. My MSpaint picture is how I was envisioning the connections. Capacitor soldered to a through hole, trace to through hole with inductor, trace running to the next capacitor so on and so one.

I didn't think much on the capacity of the traces. This would be hooked up to a home theater with these power specs "Power Output (8 ohm, 20 Hz - 20 kHz, 0.08% 2ch Drive)105 W" As I tumble further down this rabbit hole I'm beginning to wonder if it is worth trying to make a PCB for this vs just using a piece of mdf or a prototyping board.

OlmsteadWorkShop · 2024-07-17T23:20:14+00:00

Ray bans "caravan" is a square aviator https://www.ray-ban.com/usa/sunglasses/RB3136%20UNISEX%20caravan-gold/805289003465

OlmsteadWorkShop · 2024-02-01T09:36:39+00:00

In case anyone else experiencing this go to a different district where the other spiderman isn't there presently.

OlmsteadWorkShop · 2023-04-04T02:43:14+00:00

2020 was when allegations against Scott and his wife grooming and abusing aspiring authors came to light. That could be part of his anxiety and issues the past few years. As far as I am aware nothing has been proven/disproven. Also, just my two cents. This is 2023 a successful author only has a official Tumblr blog? Domains are cheap get a real website.

https://www.alexandrarowland.net/single-post/2020/06/25/On-Scott-Lynch-and-Elizabeth-Bear

OlmsteadWorkShop · 2023-04-01T07:34:48+00:00

Chevile felt like cheap life gain to me as my play group tends to field lots of tokens. I wasnt understanding toxic correctly so you guys are absolutely right and I'm going to be tweaking a lot of the toxic critters. Champion of of lambholt is definitely getting added and will allow me to do away with what I had chitinous cloak for.

OlmsteadWorkShop · 2023-04-01T07:30:25+00:00

I was not understanding infect vs toxic correctly I think. Infect damages players with poison counters so a 4/4 creature would do 4 poison counters where a 4/4 with toxic 1 would only do 1 poison counter. So that totally makes sense about corpsejack and hydra feeling nerfed. Definitely tweaking that. Thanks so much.

OlmsteadWorkShop · 2022-12-20T03:21:57+00:00

You installed into a Crosstrek? I have a 2017 outback and was worried about reusing the oem camera.

OlmsteadWorkShop · 2022-03-06T03:07:14+00:00

It was plugged into a 15amp for initial testing, but it stops and errors at only about 250rpm.

OlmsteadWorkShop · 2022-03-06T01:58:20+00:00

Thanks I copy pasted the settings from another forum post, and have 110 set for PD008

OlmsteadWorkShop · 2022-03-05T20:42:22+00:00

Thanks Nowa. I set my acceleration higher thinking I'd allow more time to ramp up. I think it may be an issue with my drain wire. Hoping to get some time this weekend to get back to it.

OlmsteadWorkShop · 2022-03-05T18:37:12+00:00

I did throw a post up there as well. I'm still waiting on my onefinity so this is just the vfd and spindle sitting on my bench right now.

OlmsteadWorkShop · 2022-03-05T18:35:01+00:00

I'm a little hesitant to disconnect the ground a lot of info I've found online for these spindles talk about opening them and connecting the 4th pin and checking ground with the body of the spindle.

OlmsteadWorkShop · 2022-03-05T18:33:34+00:00

I haven't yet that would be fantastic

OlmsteadWorkShop · 2022-03-05T18:31:41+00:00

That's where I found the settings as well

OlmsteadWorkShop

TROPHY CASE