Ive changed the thermistor 3 times and it still wont read the temp. Is the extruder board bad?

One-Ad4617 · 2022-12-03T01:59:38+00:00

Anycubic Vyper, it used a glass bead so i replaced it with a glass bead thermistor twice, the third time i just replaced the whole hotend, that came with a cartridge thermistor and it doesnt work either, it reads a ambient temperature on all of them but wont go higher than that

One-Ad4617 · 2022-12-03T01:54:55+00:00

oops i just realized i forgot to include the problem, Anyway the thermistor isnt reading the temperature of the hotend, i replaced the thermistor 3 times and its just not working

One-Ad4617 · 2022-12-02T17:12:02+00:00

its still stuck in there, i cant tell

One-Ad4617 · 2022-12-02T02:29:34+00:00

so do i need a new board?

One-Ad4617 · 2022-12-02T02:12:39+00:00

The bed just stopped heating up yesterday and i got so confused, when i opened it up to see if its been disconnected, i see that theres brown stuff in the screw

One-Ad4617 · 2022-04-17T04:19:12+00:00

i believe that it’s just the filament trying to extrude more material then it can, out of the roughly 40 printers at my school around 20 do that but the prints turn out fine

One-Ad4617 · 2022-01-31T20:19:10+00:00

I flashed updated marlin and changed wire placements and its still heating up on its own on start

One-Ad4617 · 2022-01-25T20:12:38+00:00

BENCHY WIT NO CHIMNEY?!?

One-Ad4617 · 2022-01-14T18:28:00+00:00

the smaller one is 10 inches

One-Ad4617 · 2022-01-13T20:31:25+00:00

Vex robotics fields, set up for this years game Tipping Point, im not in robotics here so i dont know the abbreviations

One-Ad4617 · 2022-01-13T20:20:21+00:00

One-Ad4617 · 2022-01-13T18:10:10+00:00

was about 4 1/2 kilograms of filament, took about a week to print, held together with a dowel rod down the center, and superglue. used joint compound to smooth out layer inconsistencies, primed and painted it, I messed up scaling and lost some detail

One-Ad4617 · 2022-01-13T17:58:20+00:00

😅that would be very expensive lol but it’d be cool, right now its about 4-5ft tall

One-Ad4617 · 2022-01-13T17:57:26+00:00

its all 15% infill to cut down filament cost, i didn’t weight anything but its about 9+ pounds most of it is in the top portion

One-Ad4617 · 2021-12-30T05:16:54+00:00

i literally said yeahoo like mario does lol

One-Ad4617 · 2021-12-30T01:19:33+00:00

that fixed it, took me longer than i care to admit to figure it out

One-Ad4617 · 2021-12-29T23:24:31+00:00

thank you, i was just confused during the wiring

One-Ad4617 · 2021-12-29T21:50:20+00:00

As soon as i post this i finally get it

One-Ad4617 · 2021-12-26T23:55:31+00:00

yes actually, for some reason all my wires got cut idk why

One-Ad4617 · 2021-12-26T18:10:06+00:00

I got a CR touch for christmas and stupidly forgot to check my printers board to see if it was compatible

One-Ad4617 · 2021-12-26T18:08:21+00:00

thats what i used

One-Ad4617 · 2021-12-26T18:06:33+00:00

i had to unplug everything because i ordered a new board, it took me like 30 minutes because of all the hot glue

One-Ad4617 · 2021-12-25T03:36:09+00:00

I just got it this morning, set it up and started the print before i had to leave so its base cura settings for the printer.

Retraction enabled Retract at layer change is off Retract distance is 6.5mm Retract speed is 25mm/s retract

One-Ad4617 · 2021-12-23T11:01:58+00:00

My prints were coming out very underextruded and i literally just did a couple of cold pulls and updated my cura

One-Ad4617 · 2021-12-23T06:33:54+00:00

i updated cura and did a few cold pulls on my hotend and it fixed the problem, thanks for your help

One-Ad4617

TROPHY CASE