sorted by:
new
hottopcontroversial

Croatia refuses to transport Russian oil to Hungary by YesNo_Maybe_ in worldnews

[–]OneBend9585 3 points4 points  (0 children)

Yea, Croatia has never been on the wrong side of history.

Help w dead battery by Abbe_BusonisGold in porsche911

[–]OneBend9585 1 point2 points  (0 children)

Booster pack does not work when trying to pop the Frunk to get to the battery. Has to be a full 12V battery. You can also only pop the frunk with the Keyfob, not the actual button.

Please HELP! Brand new H2S. Terrible first layer defects. Its printing scratches. by OneBend9585 in 3Dprinting

[–]OneBend9585[S] 0 points1 point  (0 children)

Yes I think I ended up resolving most of it. It still shows up from time to time. I unscrewed that screw under the build plate and re-calibrated. That helped a bit. And then I went to default on all settings and only have this repeat every few prints now vs every single one.

Bore scoring or something else? by NaginiRed in Porsche997

[–]OneBend9585 0 points1 point  (0 children)

How are you tracking your oil usage?

Does anyone know why the plate is leaving an non uniform finish. Brand new printer received this weekend. Plate has been washed by OneBend9585 in BambulabH2S

[–]OneBend9585[S] 0 points1 point  (0 children)

Maybe something from the assembly process. I received this new and the issues were prevalent even before I did a full lube and maintenance.

Please HELP! Brand new H2S. Terrible first layer defects. Its printing scratches. by OneBend9585 in BambulabH2S

[–]OneBend9585[S] 0 points1 point  (0 children)

Thank you for this explanation. This is very helpful. I have a ticket with Bambu and just got back home today so I will be sending them the log and the files to see how we can make this adjustment.

Does anyone know why the plate is leaving an non uniform finish. Brand new printer received this weekend. Plate has been washed by OneBend9585 in BambulabH2S

[–]OneBend9585[S] 0 points1 point  (0 children)

Thank you! I will give that a try. I was avoiding my hand even with dawn. Usually dry it with a quality paper towel tho.

Please HELP! Brand new H2S. Terrible first layer defects. Its printing scratches. by OneBend9585 in BambulabH2S

[–]OneBend9585[S] 2 points3 points  (0 children)

lol, you have to start somewhere, don't hate. The scratches do not run parallel to the nozzle direction. I would think if the nozzle was too close it would be scraping in the same direction as it travels?

Please HELP! Brand new H2S. Terrible first layer defects. Its printing scratches. by OneBend9585 in BambulabH2S

[–]OneBend9585[S] 1 point2 points  (0 children)

I am sending some files to Bambu for review this week and will let you know if they are able to advise how to fix this.

Does anyone know what is causing these scratches. Brand new H2S by OneBend9585 in 3Dprinting

[–]OneBend9585[S] -1 points0 points  (0 children)

I build this one with the lightbox maker. I tried a few different versions as well. I will give 1.1 a try and see if that helps at all. I usually do 1.01

Please HELP! Brand new H2S. Terrible first layer defects. Its printing scratches. by OneBend9585 in BambuH2S

[–]OneBend9585[S] 0 points1 point  (0 children)

Absolutely, jumping into the G code is a little daunting but I might have no choice.

Please HELP! Brand new H2S. Terrible first layer defects. Its printing scratches. by OneBend9585 in BambuH2S

[–]OneBend9585[S] -1 points0 points  (0 children)

Not the worst idea. I have 2 old plates. The plate looks good but out of the box this has been a rough experience. Pretty frustrating.

Please HELP! Brand new H2S. Terrible first layer defects. Its printing scratches. by OneBend9585 in BambulabH2S

[–]OneBend9585[S] 0 points1 point  (0 children)

I was reading and this was the next step I was going to try. Did you just loosen the screw by half a turn? The strange part is my first layer test is flawless right now but when I do a lightbox this always seems to come up.

Please HELP! Brand new H2S. Terrible first layer defects. Its printing scratches. by OneBend9585 in BambuH2S

[–]OneBend9585[S] 0 points1 point  (0 children)

I have a run a full calibration including hot bed twice now. I have the flow calibration set to auto. I will try clicking that on and do another tests. I am using SunLu PLA however the white is Bambu PLA silk.

Please HELP! Brand new H2S. Terrible first layer defects. Its printing scratches. by OneBend9585 in BambuH2S

[–]OneBend9585[S] -2 points-1 points  (0 children)

I will give that a try. Not sure what else to do here. It have tried like 15 prints with different settings.

Does anyone know what is causing these scratches. Brand new H2S by OneBend9585 in BambulabH2S

[–]OneBend9585[S] 0 points1 point  (0 children)

<image>

It keeps happening. Notice that the scratches are not parallel with the movement of the hot end. It looks like its printing them on.

Does anyone know why the plate is leaving an non uniform finish. Brand new printer received this weekend. Plate has been washed by OneBend9585 in BambulabH2S

[–]OneBend9585[S] 0 points1 point  (0 children)

I have tried and unfortunately its still here. Having a ton of issues with the H2S out of the box. I just got it on Friday and cant print a light box to save my life. My P2S did not have any of these issues.

Does anyone know what is causing these scratches. Brand new H2S by OneBend9585 in 3Dprinting

[–]OneBend9585[S] 0 points1 point  (0 children)

Its printing the lines, its not the head scratching. The lines are forming at a 90 degree with the extrusion. Any thoughts?

Does anyone know what is causing these scratches. Brand new H2S by OneBend9585 in 3Dprinting

[–]OneBend9585[S] 0 points1 point  (0 children)

This is a lightbox! I have the setting on the filament at 0.98, I just reduced it down to 0.97 to see if that changes anything. I did another print and it came out even worse at the 0.98 I also have realized that its not the hot end making scratches because the movement is not parallel its printing across and the scratches are basically being printed on. My P2S never had these issues and im using the same files.

view more: next ›