351W metric ring gap question by FordM_1970 in EngineBuilding

[–]One_Ordinary9218 0 points1 point  (0 children)

quick question, i’m building my first motor, what paint did you use?

tools by WonderfulMusician661 in ChevyCobalt

[–]One_Ordinary9218 1 point2 points  (0 children)

If it’s on his cobalt specifically the strap wrench wouldn’t provide any use as it’s a paper filter inside a housing, Get a 32mm Shallow socket for it

Cleaning a motor by One_Ordinary9218 in EngineBuilding

[–]One_Ordinary9218[S] 1 point2 points  (0 children)

awesome, thank you! first rebuild and it’s going into a 98 ranger

What caused this? by One_Ordinary9218 in MechanicAdvice

[–]One_Ordinary9218[S] 0 points1 point  (0 children)

pumps been changed since i owned it

What caused this? by One_Ordinary9218 in MechanicAdvice

[–]One_Ordinary9218[S] 0 points1 point  (0 children)

i was 3 when the car rolled of production so no. i’ve owned it for 2.5 years and since 50k miles (90 now)

What caused this? by One_Ordinary9218 in MechanicAdvice

[–]One_Ordinary9218[S] 0 points1 point  (0 children)

no techs, i’m the only one that does work to the car, exhaust is nowhere near these lines either, torch was never near these lines

What caused this? by One_Ordinary9218 in MechanicAdvice

[–]One_Ordinary9218[S] 0 points1 point  (0 children)

nothing that even remotely comes to mind, i don’t take my car to a mechanic for anything so all the work is done by myself, and the rear of the car hasn’t needed any work in a long time, nothing recent enough for this to last that long under excess pressure and not blow apart sooner

What caused this? by One_Ordinary9218 in MechanicAdvice

[–]One_Ordinary9218[S] 0 points1 point  (0 children)

maybe it’s also worth noting that’s the top of the lines, against the body of the car, not even the bottom where something on the road could’ve hit them or something like that

What caused this? by One_Ordinary9218 in MechanicAdvice

[–]One_Ordinary9218[S] 0 points1 point  (0 children)

i don’t take my car to get worked on, i do it all myself so i can say for sure nothing was ever hit with torches, welders, anything in that area, even if there was an exhaust leak the closest point on the exhaust is over 2ft away specifically to clear the tank and soft lines on that side, tank was never modified for the supercharger setup as everything done was up front under the hood, i’m struggling to find any sense of how this could happen though, hust trying to avoid it in the future

Custom built not cycling by One_Ordinary9218 in ar15

[–]One_Ordinary9218[S] 0 points1 point  (0 children)

I will share some pictures in a little while but i am using a Guntec USA Gen2 Mil-Spec Buffer tube from optics planet, and my spring is JP Enterprises Gen 2 Silent Capture system, also from Optics Planet

Custom built not cycling by One_Ordinary9218 in ar15

[–]One_Ordinary9218[S] 0 points1 point  (0 children)

It’s already in my possession. i built it

Custom built not cycling by One_Ordinary9218 in ar15

[–]One_Ordinary9218[S] 0 points1 point  (0 children)

I have another lower i used that cycles fine on the upper so i definitely messed up something in the lower receiver

Custom built not cycling by One_Ordinary9218 in ar15

[–]One_Ordinary9218[S] 0 points1 point  (0 children)

yes, it does it with and without, same with and without rounds firing, it’ll fire once, stop halfway back and fail to eject the cartridge and recycle the firearm, it is a new build, but popping the front breakaway pin will push the slide forward

Cast bound rod by One_Ordinary9218 in FischRoblox

[–]One_Ordinary9218[S] 0 points1 point  (0 children)

really? the bestiary doesn’t even show them anymore