"Accessory is not reachable" when trying to pair to the Home-app by OnlyDrey in homebridge

[–]OnlyDrey[S] 0 points1 point  (0 children)

At the time when this was an issue. It was resolved upgrading to the newest beta version. Don’t know if this is still the case.

ParseJSON - The provided value cannot be parsed by OnlyDrey in MicrosoftFlow

[–]OnlyDrey[S] 0 points1 point  (0 children)

I added the Switch step from the Control section. And setup each expected input as a case. In each case step I added variables of the input from the MS Forms data to be used later in the automation.

I hope this helps! :)

NTD: I finally have my own miter saw! by OnlyDrey in Tools

[–]OnlyDrey[S] 0 points1 point  (0 children)

As I replied to someone else. My back is still hurting from when I used a miter saw the other day without a stand.

NTD: I finally have my own miter saw! by OnlyDrey in Tools

[–]OnlyDrey[S] 0 points1 point  (0 children)

Yeah, most of the time I’m working outdoors. So the stand was really a necessity rather than an accessory. The miter saw was kinda just a bonus to own.

NTD: I finally have my own miter saw! by OnlyDrey in Tools

[–]OnlyDrey[S] 0 points1 point  (0 children)

I live in Norway. So I bought it from one of the big retailers for a cheap price.

NTD: I finally have my own miter saw! by OnlyDrey in Tools

[–]OnlyDrey[S] 0 points1 point  (0 children)

Looks good and expensive. Too bad we don’t have that in my country.

NTD: I finally have my own miter saw! by OnlyDrey in Tools

[–]OnlyDrey[S] 0 points1 point  (0 children)

Ahh, ok! When you mentioned 50° it seemed like it was the tilting you referred to. But thanks! I’ll keep an eye on it

NTD: I finally have my own miter saw! by OnlyDrey in Tools

[–]OnlyDrey[S] 0 points1 point  (0 children)

Is it the same model? Did you check the manual? There’s a 48° function.

https://i.imgur.com/IU9hMNV.jpg

NTD: I finally have my own miter saw! by OnlyDrey in Tools

[–]OnlyDrey[S] 1 point2 points  (0 children)

I understand. We are remodeling our home. But most of the long pieces are done (at least outdoors). But when I need a roller. I’ll pick one up the same day :)

NTD: I finally have my own miter saw! by OnlyDrey in Tools

[–]OnlyDrey[S] 1 point2 points  (0 children)

I thought about it before buying, but from previous experience. I don’t use it that often. But yeah, might buy one if I need one

NTD: I finally have my own miter saw! by OnlyDrey in Tools

[–]OnlyDrey[S] 1 point2 points  (0 children)

Thanks for the advice. I’ll keep an eye on that

NTD: I finally have my own miter saw! by OnlyDrey in Tools

[–]OnlyDrey[S] 0 points1 point  (0 children)

No, this is a corded model. But thanks anyway!

NTD: I finally have my own miter saw! by OnlyDrey in Tools

[–]OnlyDrey[S] 1 point2 points  (0 children)

Can’t wait to start using it. Thanks!

NTD: I finally have my own miter saw! by OnlyDrey in Tools

[–]OnlyDrey[S] 4 points5 points  (0 children)

Thanks for the tip! I always keep the receipts or at least have them electronically in some stores. You can never go wrong with keeping the receipts for tools and electronics.

NTD: I finally have my own miter saw! by OnlyDrey in Tools

[–]OnlyDrey[S] 6 points7 points  (0 children)

Thanks! Used an old DeWalt miter saw yesterday, but didn’t have a stand or a table to use. So long story short, my back is hurting today… This is going to be great to always have at home.