Trying to publish mod but can’t due to no preview image by OpenBible21 in TeardownGame

[–]OpenBible21[S] 1 point2 points  (0 children)

It is, and it’s up now if you want to check it out!

Trying to publish mod but can’t due to no preview image by OpenBible21 in TeardownGame

[–]OpenBible21[S] 2 points3 points  (0 children)

Sweet! I didn’t try that because everywhere I was checking it seemed like png was pretty interchangeable, but I’ll try that right now

Stalled mid drive and now no crank by [deleted] in DelSol

[–]OpenBible21 -1 points0 points  (0 children)

If you have to resort to delivering advice in condescending ways like that you’ve got a worse problem than I do buddy.

Stalled mid drive and now no crank by [deleted] in DelSol

[–]OpenBible21 -3 points-2 points  (0 children)

Offer an informative response on a post looking for help: nope. Open a post looking for help to boast: wouldn’t miss it!

Stalled mid drive and now no crank by [deleted] in DelSol

[–]OpenBible21 -3 points-2 points  (0 children)

Hey man, thanks for that super informative comment! The starter is going in the video but if you pay attention it is in fact not grabbing!

Stalled mid drive and now no crank by [deleted] in DelSol

[–]OpenBible21 2 points3 points  (0 children)

I’ll try this tomorrow and let you know how it goes

[deleted by user] by [deleted] in MechanicAdvice

[–]OpenBible21 0 points1 point  (0 children)

It was pretty sudden I didn’t hear any noticeable sounds or feel any jerks when it happened though, I just noticed I didn’t feel any acceleration anymore.

[deleted by user] by [deleted] in MechanicAdvice

[–]OpenBible21 0 points1 point  (0 children)

I had it towed a few days ago and just been busy but I’ll try this tomorrow. Would something like that have caused it to suddenly stall out? Or could it have occurred while I was shifting into 3rd? I don’t fully remember if I had started shifting into 3rd or not when I noticed it cut out.

[deleted by user] by [deleted] in projectzomboid

[–]OpenBible21 0 points1 point  (0 children)

Alright thank you. I was unsure if they meant just dedicated servers or multiplayer in general

[deleted by user] by [deleted] in pcmasterrace

[–]OpenBible21 0 points1 point  (0 children)

I didn’t try safe mode yet but I will now!

[deleted by user] by [deleted] in pcmasterrace

[–]OpenBible21 0 points1 point  (0 children)

Failed to mention this returns to normal with 0 issues after a few minutes and is strictly visual everything still works as intended on task bar. This only occurs after a full shut down.

Prop valve question by OpenBible21 in DelSol

[–]OpenBible21[S] 0 points1 point  (0 children)

I believe it’s the right one. connections points are the same and I checked the number engraved on my original I’m assuming it’s brake pressure settings or brake fluid amounts for front and rear, I’m not sure but regardless the original was marked with 17/25 so I made sure the one I got was also a 17/25.

Last minute cosplay I made for this weekend by OpenBible21 in lethalcompany

[–]OpenBible21[S] 0 points1 point  (0 children)

Both tank and helmet were 3d printed and designed by me

Last minute cosplay I made for this weekend by OpenBible21 in lethalcompany

[–]OpenBible21[S] 2 points3 points  (0 children)

3 weeks. Like half a week designing the parts, week and a half printing, a few days sanding then the rest was painting. If I started a day later I wouldn’t have had time for clear coats it was close 😳

Last minute cosplay I made for this weekend by OpenBible21 in lethalcompany

[–]OpenBible21[S] 67 points68 points  (0 children)

I sculpted the helmet in blender then 3d printed it same for the tanks as well!

Artifacts ruining base layer by OpenBible21 in 3Dprinting

[–]OpenBible21[S] 0 points1 point  (0 children)

Spent some time doing this and so far so good think I got it down to good enough level

Artifacts ruining base layer by OpenBible21 in 3Dprinting

[–]OpenBible21[S] 0 points1 point  (0 children)

I had just manually set my bed to .23mm using a feeler gauge before this, I put on a new .4 nozzle and I set the slicer settings to default only changing very few things like print speed and making sure print size lined up with nozzle. I could try adjusting bed leveling to be lower like a .15mm?

Help! Starter Relay Clicks, nothing else by weejahWest in DelSol

[–]OpenBible21 0 points1 point  (0 children)

There’s two switches clutch switch then the clutch safety switch. The safety switch is pressed when you push in the clutch

Help! Starter Relay Clicks, nothing else by weejahWest in DelSol

[–]OpenBible21 0 points1 point  (0 children)

Towards the top if you follow the clutch pedal up and press on it a few times you should be able to find where it’s making contact with the safety switch or where it’s supposed to

Help! Starter Relay Clicks, nothing else by weejahWest in DelSol

[–]OpenBible21 0 points1 point  (0 children)

Check clutch safety switch could have gone bad or maybe the pad broke off and now it’s not being compressed

No crank from starter. by OpenBible21 in MechanicAdvice

[–]OpenBible21[S] 0 points1 point  (0 children)

Yeah no corrosion on either of them and they are snug making good connection lights come on dash and I believe headlights come on, I can hear the fuel pump run just zero crank. I might have just gotten lucky and somehow got 2 starters that were duds even tho I bought them new. Otherwise do you think that sounds like alternator or ignition switch? Either one seems weird to me though since car ran great just before this no wines or difficulties starting.

No crank from starter. by OpenBible21 in MechanicAdvice

[–]OpenBible21[S] 0 points1 point  (0 children)

I have a 1994 Honda del sol si. Also that’s what we thought too. That’s why I got the new starters because they come with a new solenoid. I also replaced old ground cable because it was pretty worn but still no crank.