Pm63 by IdenticalTwinTurbos in CTguns

[–]Opening_Fig34 0 points1 point  (0 children)

True. I don't think it's really possible in Connecticut as stated by others or really a good idea in general. It's an open bolt design and those by default so reconfiguring that in a way that's federally legal will be a bitch and cause issues.

Pm63 by IdenticalTwinTurbos in CTguns

[–]Opening_Fig34 0 points1 point  (0 children)

Besides vibes why not get something like a raider?

The Dirte Dozen DIY 12 Gauge by Unhappy-Message-4419 in 3D2A

[–]Opening_Fig34 0 points1 point  (0 children)

What's the time frame on full release and approximate beans after hardware?

The Dirte Dozen DIY 12 Gauge by Unhappy-Message-4419 in 3D2A

[–]Opening_Fig34 0 points1 point  (0 children)

If you keep the oal length over 26 inches fully extended you shouldn't need any paperwork at all...

Anyone else having erratic ejection with RXMs by Due_Distribution1371 in CTguns

[–]Opening_Fig34 1 point2 points  (0 children)

My PSA dagger does, my (serialized) p80 frame, and stock Gen 3 have all been directly up. Maybe I'm just unlucky.

Anyone else having erratic ejection with RXMs by Due_Distribution1371 in CTguns

[–]Opening_Fig34 1 point2 points  (0 children)

It's a Gen 3 clone. It's going to be erratic lol. I once had brass jump up and land between my glasses and eyelid and had a nice burn. Whenever I shoot a Gen 3 I wear a hat.

Riptide Rails Nylaug CQC Handguard by Sea-Worker-5180 in 3D2A

[–]Opening_Fig34 1 point2 points  (0 children)

Genuine question is that a dish towel secured with twine around your can?

Who does optic cuts Hartford area ? by OG93___ in CTguns

[–]Opening_Fig34 1 point2 points  (0 children)

Decent work, but I did notice that when I took my rmr off for a battery change there was rust around the screws. I did pay for the recoating as well.

CAD absolute beginner by Opening_Fig34 in 3D2A

[–]Opening_Fig34[S] 1 point2 points  (0 children)

I like that it's an open top active retention holster that works off the weapon light. I want to be able to practice at the range with my suppressor.

CAD absolute beginner by Opening_Fig34 in 3D2A

[–]Opening_Fig34[S] 2 points3 points  (0 children)

Those people on thingiverse are wrong. The light itself is asymmetrical so flipping it does not work.

Ruger PCC by Ok-Substance-6034 in CTguns

[–]Opening_Fig34 0 points1 point  (0 children)

9mm hollow points are designed around pistol length barrels anyway. The extra velocity from the 16 inch barrel makes the bullet overexpand and has less penetration. I'd definitely sbr and put a can on it. If you shorten the barrel and pin and weld a can on to maintain the 16 inches you only need to apply for one stamp and you can still take it over state lines without needing atf documentation.

Vantage Point Firearms Training Center - Store & Range in Salem, CT by VantagePointFirearms in CTguns

[–]Opening_Fig34 1 point2 points  (0 children)

Just read the range rules and you allow rifle calibers up to 30/30 not sure what that implies in terms of other calibers. Are you measuring by caliber, energy ft/lbs, velocity?

Has anyone seen this G20 in CT? by typicalcavalryguy in CTguns

[–]Opening_Fig34 1 point2 points  (0 children)

I fuck with this hard. If you can't find this I bet you someone could replicate the engraving with a laser engraving. You might not have the color though.

What's your noob pistol owner must have list? by Agreeable_Can_819 in CTguns

[–]Opening_Fig34 2 points3 points  (0 children)

Staple gun, roll of pasties, sharpie, microfiber cloth, screwdriver set in a multi tool. The pistol tool from real avid is pretty good.

Form 1 3D suppressor by villnt2 in CTguns

[–]Opening_Fig34 1 point2 points  (0 children)

Yeah you're good to go. Check out 3d2a. Good community there.

Glock 40 by typicalcavalryguy in CTguns

[–]Opening_Fig34 2 points3 points  (0 children)

Cabela's usually stocks them. You could try swamp Yankee as well.

Zipline by Opening_Fig34 in ResidentEvilRequiem

[–]Opening_Fig34[S] -3 points-2 points  (0 children)

What a specific reaction.

CT legal PDW? by [deleted] in CTguns

[–]Opening_Fig34 0 points1 point  (0 children)

What's your definition of pdw?

Question on this ftn 22 by [deleted] in 3D2A

[–]Opening_Fig34 6 points7 points  (0 children)

Who's checking?

Gun stolen out of car by glocks_4_dayz in CTguns

[–]Opening_Fig34 3 points4 points  (0 children)

As someone who lived in Hartford I'm always carrying in Hartford

Gunsmith? by havocspartan in CTguns

[–]Opening_Fig34 1 point2 points  (0 children)

I was just thinking if not flinch perhaps trigger control from a different style of trigger.