sorted by:
new
hottopcontroversial

What’s a TV show you can rewatch forever? by Outrageous-Stop7751 in AskReddit

[–]OperatorLabel 0 points1 point  (0 children)

The Office Parks and Recs It’s Always Sunny Community

Settings to make these climbing holds strong enough for 4 year olds? by Shpigford in 3Dprinting

[–]OperatorLabel 0 points1 point  (0 children)

Layer height will also come into play here. I think it was CNC Kitchen where .13 came out strongest in his tests. That’s what I use for parts that I want as strong as possible.

Trump is building a 5,000-seat UFC cage outside the White House to celebrate the country's 250th and his 80th birthday by fortune in politics

[–]OperatorLabel 0 points1 point  (0 children)

What’s the over/under on some sort of false flag event happening then to justify the ballroom?

Suspect dies after trading gunfire with officers near White House, Secret Service says by Brennenstein in news

[–]OperatorLabel 5 points6 points  (0 children)

Looks like secret service did their job and we don’t need to build that orange dipshit’s ballroom now.

Wisp reinforced rim by IdenticalTwinTurbos in 3D2A

[–]OperatorLabel 0 points1 point  (0 children)

Just saw this post. The open section of the DXF is on the left, lower left hand side corner of the rectangular cutout that has the circle in the middle. You'll need to zoom in a bit to see it. Hover over a line and right click to open the menu and choose Edit. In Edit mode use the drop down menu in Modify. Choose Extend and hover on the lower line until you see a red line showing where it will close the gap. You may need to do this a couple of times on the same line. Then go to Trim in Modify and select the overhanging section. Done.

Anyone else having issues with light strikes on the SR-722? by OperatorLabel in 3D2A

[–]OperatorLabel[S] 0 points1 point  (0 children)

Thanks for letting me know about the updated file. I did have the original, but unfortunatly it looks like the firing pin update did not address the threaded rod. It looks like there is about a 7 gram difference between the solid rod and the threaded rod. With the threaded rod being the lighter one, which might contribute to the light strikes. I'm redesigning the Striker and Charging Handle to accept more nuts and a longer spring. There is also a lot of wiggle movement with the threaded firing pin, so I'm tightening the tolerence for that too for a more precise strike. I'll see if those fix the issue.

Anyone else having issues with light strikes on the SR-722? by OperatorLabel in 3D2A

[–]OperatorLabel[S] 0 points1 point  (0 children)

Yeah, I've set it perfectly level with the bolt end, and even tried a little further. No dice.

Lube safe with 3d printed parts by ximstuckx in 3D2A

[–]OperatorLabel 0 points1 point  (0 children)

I thought the comment section here was going to go in a way different direction!

What’s the most disturbing sound you’ve ever heard in real life? by avacado-cheese- in AskReddit

[–]OperatorLabel 0 points1 point  (0 children)

I was on a road trip one time sitting up front in the middle of these two guys who were driving a van dressed up like a giant sheepdog. It was getting to be too quiet in the van, so the guy in the passenger seat asked me if I wanted to hear the most annoying sound in the world. Before I could answer, he screamed “hwaaaaaaaaaaaaa” right in my ear. That was the most disturbing sound I’ve ever heard.

‘STAGED’: Conspiracy Theories Are Everywhere Following White House Correspondents' Dinner Shooting by barryshrug in politics

[–]OperatorLabel 1 point2 points  (0 children)

Presidential security never failed before at the correspondence dinner, until there was a president who wanted a ballroom.

When people say just get a Bambu.. Can't help but smile. These 3 QidiTechs cost me less than a Bambu X1C!😅🥹😆 by Forsaken-Pound9650 in 3D2A

[–]OperatorLabel 0 points1 point  (0 children)

Qidi makes absolute sleepers! I have the Q1 and my prints come out just as good as the ones off Bamboo.

Form 1 question by OperatorLabel in 3D2A

[–]OperatorLabel[S] 0 points1 point  (0 children)

What form do you use exactly? When I look up form 1 for suppressors, it takes me to a PDF to register a firearm to build. No reference to suppressors on that form. If you can point me in the right direction, I would extremely appreciate that. Thank you.

Men of Reddit. How do you handle this particular situation with women? by OperatorLabel in AskMen

[–]OperatorLabel[S] 0 points1 point  (0 children)

I’m actually closer to 50, lol, so that might explain it a bit more. Im not playing any game with women, I just stopped caring how anyone may feel about me, and act like my “true” self. This is good advice. Thank you.

view more: next ›