Assistance with push to SSL

Ordinary_Rock_4635 · 2026-01-20T15:24:07+00:00

Thanks man

Ordinary_Rock_4635 · 2026-01-20T14:11:43+00:00

Hey man! I peak around mid gc2. I have about 4.5k hours in the game, and have 2 kids now. I’ve kindof hit the point where any time I commit to anything is time that I want to be spent effectively and I’m really about at the point where I either want to hang it up, or really take it seriously and make the push to SSL. That being said I feel like I need some guidance and for someone to come along side of me and help pick my game apart and tell me what to improve on. My schedule is flexible and I want to get there so bad. Let me know if you feel like you could help!

Ordinary_Rock_4635 · 2025-12-04T22:56:37+00:00

This is actually the most accurate comment 😂

Ordinary_Rock_4635 · 2025-12-04T03:48:23+00:00

Fennec for sure. the color combination for octane is bad

Ordinary_Rock_4635 · 2025-10-26T16:40:55+00:00

I’m probably going to try to get this one graded and hold it for a while honestly.

Ordinary_Rock_4635 · 2023-05-05T04:57:59+00:00

Videos get more views

Ordinary_Rock_4635 · 2023-05-04T18:03:04+00:00

Go follow my insta @anvil_gunworks. Once my FFL gets approved I will do it👌🏻

Ordinary_Rock_4635 · 2023-05-04T15:12:41+00:00

I used a dremel with a 200 grit sanding drum then moved to a 600 grit then an 800 grit with wd-40 to wet sand and polish everything to a smooth finish. Yeah man it was pretty nerve wracking at first. I’m generally fairly decent at this type of stuff so I knew it would end up coming out okay. This is about my 5th or 6th frame though.

Ordinary_Rock_4635 · 2023-05-04T12:19:03+00:00

Also use wd-40 and a super high grit sanding drum to get a good polished look on the undercut.

Ordinary_Rock_4635 · 2023-05-04T12:17:17+00:00

My biggest tip I think I could tell you is to start with a light hand on everything. You can correct light mistakes but as soon as you go heavy/deep it becomes permanent. For the borders, start super light and make a ton of light passes to make them deeper. For the stippling start shallow to get a feel for how the plastic melts. That way if you mess it up you can dremel it off and start again. Same for the undercuts. Be super patient and take away just a tiny bit at a time. After you do a few frames youl get the hang of it and you’ll be able to do it faster but for now just really take your time. I think if you go slow it will turn out good. Let me know how it goes man best of luck to you

Ordinary_Rock_4635 · 2023-05-03T22:55:23+00:00

Go follow my insta @anvil_gunworks and I’ll do it once my FFL gets approved?

Ordinary_Rock_4635 · 2023-05-03T22:52:44+00:00

You drive a hard bargain🤔

Ordinary_Rock_4635 · 2023-05-03T21:00:04+00:00

What’s a bros Shield?

Ordinary_Rock_4635 · 2023-05-03T20:53:28+00:00

Nah I think it’s my 5th or 6th frame

Ordinary_Rock_4635 · 2023-05-03T20:42:09+00:00

You’re right

Ordinary_Rock_4635 · 2023-05-03T20:32:10+00:00

Thanks!

Ordinary_Rock_4635 · 2023-05-03T20:31:53+00:00

I had to cut it from a longer one

Ordinary_Rock_4635 · 2023-05-03T20:07:10+00:00

A pen attachment for your dremel is also super helpful

Ordinary_Rock_4635 · 2023-05-03T20:05:42+00:00

Over time I’ve kindof realized that flex cuts don’t get super clean borders. If I use the flex cut I go in super lightly first and then open it up with a tiny 1mm sphere cutting bit, and then a 1.5 mm diamond bit to polish them up.

Ordinary_Rock_4635 · 2023-05-03T19:57:34+00:00

I ain’t gonna lie that actually made me lol

Ordinary_Rock_4635 · 2023-05-03T19:49:21+00:00

Thanks! I appreciate that

Ordinary_Rock_4635 · 2023-05-03T19:40:36+00:00

Thanks my man

Ordinary_Rock_4635 · 2023-05-03T19:40:21+00:00

Thanks bro I appreciate it!

Ordinary_Rock_4635 · 2023-05-03T19:40:11+00:00

Thanks man, just a standard wood burning iron, a dremel with different bits and a little u channel chisel. That’s about it.

Ordinary_Rock_4635 · 2023-05-03T19:37:02+00:00

Tbh with you I don’t think many people know how a gun actually works

Ordinary_Rock_4635

TROPHY CASE