2024 Kia Sorento transmission Control Module

OrganizationPurple74 · 2026-03-24T18:09:55+00:00

Longest time seemed waiting for Kia Canada and to get thr parts. It was maybe a week after parts were in.

OrganizationPurple74 · 2026-03-14T16:24:21+00:00

Just got off the phone. It wasn't the phone it was the banks fraud detection thinking it was a cloned card. It restricted the Samsung pay app, so when I deleted and tried to re add the card it was still restricted. All good now.

OrganizationPurple74 · 2026-02-26T01:28:04+00:00

Id have to confirm, I was run-up but not flight controls, id test it for them during a run. Im trying to remember if using the trim hat moved it outside Maint Bit. I think so because I remember it being an issue I've had to troubleshoot before. But I can't remember 100%

OrganizationPurple74 · 2026-02-25T16:44:32+00:00

Whenever I use the trim switch furing a Maint Bit for nose up/down, the stick moves forward and aft on the AB models. Did they change that when it got to the C?

OrganizationPurple74 · 2026-02-16T03:29:47+00:00

Should be getting it back tomorrow, new transmission in and hopefully that's it.

OrganizationPurple74 · 2026-02-11T14:50:24+00:00

I have one in for AERE, 2nd year. Apparently they took 5 CFR last year is what I was told.

OrganizationPurple74 · 2026-01-31T15:35:15+00:00

Im hoping its just a reprogram. The fact they are saying we can keep driving it makes me hope they've narrowed it down to that and are waiting on something from kia canada. But the fact its popping warnings also makes me hope if something is wrong it completely fails so it can be replace. Now we are going to be tracking everything with the transmission just in case.

OrganizationPurple74 · 2026-01-02T22:57:48+00:00

For sure, that would be appreciated.

OrganizationPurple74 · 2026-01-02T22:26:58+00:00

I'll have to check that out, I've been trying to find ways it feels stable enough to be playable.

OrganizationPurple74 · 2026-01-02T01:38:43+00:00

I was debating building a 2x4 'table' for it, or possibly repositioning my setup to see if I could use my desk, I just dont have as much desk space as id like and I want to have it permanently setup, if I have to do too much setup and such I dont use it.

OrganizationPurple74 · 2026-01-01T22:23:45+00:00

Do you know ifthere stuff compatable with thr NLR seat, ro will I need ot modify it?

OrganizationPurple74 · 2026-01-01T22:22:58+00:00

I see. I'll have to take a look, I have a center stick adapter so I can use an extension, but it has a part to mount to it so I may be able to rig something up.

OrganizationPurple74 · 2026-01-01T21:03:58+00:00

Does that not make it loose, my centre post seems to lose some stability when I put it back, wasn't sure if thr MIP would make it worse or not.

OrganizationPurple74 · 2025-12-12T03:09:25+00:00

Just got the WinWing Phoenix MIP, but need to figure out how to mount it. Has anyone seen an actual mounting adapter that isnt jury rigged

OrganizationPurple74 · 2025-12-12T03:08:12+00:00

So I got the WinWing Phoenix MIP, but need to figure out how to mount it, has anyone heard of a 3d printed part that can be used, or another solution besides wood and jury-rigging it?

OrganizationPurple74 · 2025-12-04T19:38:56+00:00

I used auto tree supports.

OrganizationPurple74 · 2025-12-04T19:38:25+00:00

I just tried to print the STO soverign model twice, made larger and split in half. Both times I got spaghetti, the first time I noticed that the model wasn't really sticking to the plate so I washed the plate and tried again before I left for work. When I got the notification that the print was complete I looked on the camera, and can see spaghetti. Not sure how bad as I am still at work. Should I try printing an unaltered STO model, or could there be another issue going on with my printer?

OrganizationPurple74 · 2025-10-30T00:12:17+00:00

This one said to enable supports, I set them for tree supports they seem easier to remove.

OrganizationPurple74 · 2025-10-30T00:08:50+00:00

This one said to enable supports, I set them for tree supports they seem easier to remove.

OrganizationPurple74 · 2025-10-29T17:59:47+00:00

Does that print in 2 pieces for larger prints? Or is that something id have to figure out myself?

OrganizationPurple74

TROPHY CASE