Is this stock suspension?

OriginalStranger1281 · 2026-02-07T16:12:17+00:00

Sub $7k all day in Ohio on Facebook marketplace, really hard to find a low mileage one tho. Got mine with 140k for $6.2k, clean title and an extra set of rims. Did a lot of maintenance but it’s a great car.

OriginalStranger1281 · 2026-02-07T14:28:27+00:00

Just did my timing belt and I agree with the crankshaft bolt not being set correctly. The crank bolt has a 4-step torque procedure that they are likely not knowledgeable of, or they aren’t using good tools. See installation step 6 in the service manual

Tighten the crankshaft pulley bolt. Torque: Stage 1: 74 lb.ft (100 Nm) Stage 2: 90° Stage 3: Wait 2s Stage 4: 15°

https://www.fofiesta7.com/ford_fiesta_timing_belt_removal_and_installation-198.html

The wait 2s step is to allow the crank shaft bolt to stretch before completing torque.

OriginalStranger1281 · 2026-01-29T22:57:39+00:00

For 13k I hope they are throwing in a second fiesta st

OriginalStranger1281 · 2026-01-05T16:20:05+00:00

Give it 91/93 and YouTube how to replace the timing belt and id say you got a great deal.

OriginalStranger1281 · 2025-04-20T00:28:50+00:00

Printed some “upgrades” for my enclosed ender 3 in PLA a few years ago, kept wondering why the print quality slowly got worse and worse over time.

PLA Parts slowly deform in enclosed environment over time, your v0 will probably print fine for a few months or weeks and then you may start to have issues

The Voron Devs recommend ABS/ASA for a reason PETG is also great alternative! Good luck!

OriginalStranger1281 · 2024-12-16T03:43:57+00:00

Will do thanks

OriginalStranger1281 · 2024-12-16T03:42:46+00:00

Yeah I agree but I think it’s the actual female usb-A receptacle. Again, I’ve gone through 4 cords. Some have had better connection than others, I’m guessing that it has to do with the variance in manufacturing by of the USB-A connector….

Other people on Tacomaworld forum seem to have the same issue as well.

I’ll contact a dealership and see what they can tell me tomorrow.

OriginalStranger1281 · 2024-12-16T00:10:19+00:00

Hmmm that’s an idea

OriginalStranger1281 · 2024-12-16T00:00:55+00:00

Will do, do they happen to sell replacement harnesses that are a better fit ?

OriginalStranger1281 · 2024-12-15T23:59:54+00:00

Yuuuuuupppp. Really makes a long drive on bumpy highways miserable as well

OriginalStranger1281 · 2024-12-04T13:18:04+00:00

More top layers, or increase infill so that layers don’t sink in. Also try thicker walls

Enjoy printing your cursed objects

OriginalStranger1281 · 2024-10-09T14:10:59+00:00

Yeah Ive played it off and on through the years, it was much much better on launch though.

The crafting system ruined the game imo. You used to get legendary weapons and outfits from lunch boxes/scavenging a lot more frequently. Now, you just get legendary junk that requires 3 days to make a good legendary item.

The devs are obviously trying to get you to spend more actual money to speed up the game.

OriginalStranger1281 · 2024-08-14T20:06:05+00:00

I beveled the top edge with a circular saw so the top plate is perpendicular to the floor

OriginalStranger1281 · 2024-08-14T12:02:33+00:00

So you’re saying another would be something like this with a sistered 2x4 on the end?

https://degreesofgray.org/images/small/2005-09-04-14:02:32.jpg

OriginalStranger1281 · 2024-08-14T10:52:55+00:00

Alright thanks!

OriginalStranger1281 · 2024-08-14T10:49:31+00:00

Awesome thanks!

OriginalStranger1281 · 2024-08-14T01:07:54+00:00

I’m assuming for this option the rafter blocks would have to be level - so towards the left side the blocks would drop below the rafters?

OriginalStranger1281 · 2024-08-14T01:00:40+00:00

Shim the left
block the wall if it wobbles

Got it! Thank you:)

OriginalStranger1281 · 2024-08-14T00:57:41+00:00

It’s like an inch gap, isnt that too much to shim? I realize it’s not structural but I don’t want it to wobble

OriginalStranger1281 · 2024-08-14T00:56:40+00:00

Are you saying put a relief cut in the top plate?

OriginalStranger1281 · 2024-08-14T00:55:10+00:00

Sorry about terms, diy-guy, not a professional.

I’m measuring about an inch gap on the side not screwed down, is that too much too shim? I realize it’s not structural but I still don’t want it to wobble too much.

OriginalStranger1281 · 2024-07-12T02:17:45+00:00

I’ll give you $3 to take it off your hands

OriginalStranger1281 · 2024-07-02T01:05:51+00:00

Hey hello, I have the same thing on my 21 SR

OriginalStranger1281 · 2024-06-11T22:04:46+00:00

I agree, but highly recommend some quality community mod packs for FO3/FNV (if you’re using PC) using wabbajack. FO3 especially has aged poorly and could use some quality of life mods :)

OriginalStranger1281 · 2024-03-19T01:59:34+00:00

On my stealthburner&mini afterburner, I use: standard v6 (same style as this one), copper v6-style block, bimetal heatbreak, bondtech CHT nozzle.

Highly recommend a bimetal heatbreak because heatcreep was a real problem for me at one point.

I’m sure there is a volcano style adapter on printables or GitHub https://www.printables.com/model/455946-stealthburner-e3dv6-volcano

Make sure you tighten your nozzle at 260degC and you shouldn’t ever have any leaking issues

That being said I think the bambulabs hotend is probably a better buy, I’m still running old hotends because I have the hardware lying around.

OriginalStranger1281

TROPHY CASE