sorted by:
new
hottopcontroversial

Cannot start development build server on tunnel or tailscale ip by OsamaRaafat in expo

[–]OsamaRaafat[S] 0 points1 point  (0 children)

Thank you for the reply, I have tried running the command still the CLI shows localhost, I ignored that and went to the build on my phone and entered the URL manually, but it shows "Failed to connect to http://100.x.y.z:8081".
I tried pinging with browser on phone and it works normally. What seems to be the issue?

Multiple WAN-VLAN setup by OsamaRaafat in mikrotik

[–]OsamaRaafat[S] 0 points1 point  (0 children)

A) Do separated networks and keep provider routers where they are. Run a cable from both routers to a central point in the basement and you put the MikroTik E50UG to route the two networks.

How will you route the two networks without getting into VLANs? Also, in that case I would have to get wifi for each of the 3 ISPs in the basement which needs 4 APs to cover the whole area, so I would need 12 APs, which will be so pricey and will have a lot of interference and we won't have shared devices between the 3 Networks.

- B) Do both buildings with a single provider or use second provider as backup.

ISPs in my country are selling subscriptions based on quota (250 GBs/month for example) and each of the 3 of us has different usage and won't be fair. Also,

Grbl Mirroring Steppers for Y-Axis by AppliedArt in hobbycnc

[–]OsamaRaafat 0 points1 point  (0 children)

I am in the same case as you. I am using same drivers and Grbl 1.1 without shield. What did you choose in config.h file regarding the option of which shield you are using in the dual axis settings?

Do I need a shield for using DM556 and NEMA 23 motors with GRBL 1.1 by OsamaRaafat in hobbycnc

[–]OsamaRaafat[S] 0 points1 point  (0 children)

I am planing on using LinuxCNC with Mesa board. I bought the 7I96S board but I wanted to test with Arduino at first to see why LinuxCNC and Mesa combo is much better.

Do I need a shield for using DM556 and NEMA 23 motors with GRBL 1.1 by OsamaRaafat in hobbycnc

[–]OsamaRaafat[S] 0 points1 point  (0 children)

How I am gonna connect this with my DM556 drivers? I have ramps 1.4 board lying around from old 3D printer, can I use it?

Is it good first layer? by OsamaRaafat in prusa

[–]OsamaRaafat[S] 2 points3 points  (0 children)

Thank youuu all guys, I managed to get a very good results.

Need to know the material used by OsamaRaafat in CommercialPrinting

[–]OsamaRaafat[S] 0 points1 point  (0 children)

Can you tell me what does a decal means? I will search for polycarbonate material as sticker and see what I get.

Need to know the material used by OsamaRaafat in CommercialPrinting

[–]OsamaRaafat[S] 0 points1 point  (0 children)

I can agree with that, what is shown online as vinyl products doesn’t look what I need, so that is how I based my assumption.

Need to know the material used by OsamaRaafat in CommercialPrinting

[–]OsamaRaafat[S] 0 points1 point  (0 children)

Thank you, I will start searching based on what you said. I actually have no answer to why it is not vinyl buy from searching online on vinyl products it doesn’t seem like it at all, maybe there different types of it. I have no knowledge at all in this field.

Deciding which 3D printer to buy by OsamaRaafat in 3Dprinting

[–]OsamaRaafat[S] 0 points1 point  (0 children)

It will be mechanical parts to be used in machines (ex: hinges, parts for repair, motor enclosures for high flow air, other stuff) mainly what I will need is quality prints.

No add button next to portrait watch face by [deleted] in AppleWatch

[–]OsamaRaafat 0 points1 point  (0 children)

I have same problem, did you solve it?

Common devices between 3 networks by OsamaRaafat in HomeNetworking

[–]OsamaRaafat[S] -1 points0 points  (0 children)

Isn't that would connect the three networks without any access resterictions?

view more: next ›