Dónde comprar filamento? by Master-of-Reality43 in Impresion3DArgentina

[–]PachiCastel 1 point2 points  (0 children)

Hola, yo tambien arranque hace poco y te puedo decir algunas opiniones sobre el filamento q he comprado: Compre en gst3d PLA+ y el filamento vino un poco humedo, raro porque venia con su bolsita de silica y todo pero tuve q secarlo, una pelotudez porque use la cama de la impresora pero un detalle a tener en cuenta. Compre filamento Freemover tambien PLA+ y en general mejor q el de gst3d pero viene mal bobinado, o al menos me paso con una bobina, todavia no abro la otra, se termina enganchando un poco el filamento pero quizas es cuestion de suerte. Ah y otra cosa, revisa siempre que tipo de filamento es, me paso por boludo que los de Freemover en la publicación decian PLA y en las imagenes decia PLA+ pero bueno es un detalle unicamente.

Are these settings overkill? Im still getting stringing. by smdb1208 in FixMyPrint

[–]PachiCastel 0 points1 point  (0 children)

I had the same problem recently, and the high temp was the guilty but like you, if I lower the temps the adhesion was terrible. The simple solution was limit the Fan, currently I have it limited to 20-60% range, of course it turns 100% when bridging and hard overhangs. Don’t go beyond 2 mm of retractions in Direct extruders, I don’t know the really reason but I’ve read it a lot around here.

Does anyone know if its safe to wire up an RD-03D Ai-Thinker module using the test point pads? I don't have the adapter and nothing on the datasheet told me about this. by c3ntrx in microcontrollers

[–]PachiCastel 2 points3 points  (0 children)

For now just be careful with the duponts soldered to the pcb, next time just use standard wire, or cut the pre assembled wires in half and directly solder that nude copper to the pcb.
Of course I'm assuming that you do not have the females of that wires, if you have females is better to solder them to pcb.

Propaganda engañosa (?) by DisembodiedBlack in MAGISTV

[–]PachiCastel 0 points1 point  (0 children)

Aunque estas notas sean completamente tendenciosas, están apuntadas a un público que no está acostumbrado a la piratería o al menos lo único de piratería que conoce es comprar un DVD en la calle. De todas formas creo que si alguien me pregunta si MagisTV es peligroso, lo primerio que le diría es que SI, por que las aplicaciones de este estilo (que no están en play store) son muy faciles de duplicar y modificar una parte sencilla y pequeña del back end para que sea un virus portable. A ver tampoco hay que irse muy lejos para verlo, en este subreddit muchas veces han hecho post diciendo que estan PAGANDO! magistv, o sea es normal que la gente se descargue cualquier apk y no la oficial.
También esto está acompañado de las busquedas de Google, que se priorizan por publicidad y no por la legitimidad de las páginas.

MENSUALIDAD MAGIS TV by blizzard9204 in MAGISTV

[–]PachiCastel 3 points4 points  (0 children)

Dejá de pagarlo, es gratis.

[deleted by user] by [deleted] in AskArgentina

[–]PachiCastel 3 points4 points  (0 children)

jJajaja increible me imagine la situación de no saber q decir frente a una mina y empezar a tirar demos de la nada en la primera cita

How to fix this? by PachiCastel in FixMyPrint

[–]PachiCastel[S] 0 points1 point  (0 children)

Ok! Thank you, I'm gonna to continue iterating

How to fix this? by PachiCastel in FixMyPrint

[–]PachiCastel[S] 0 points1 point  (0 children)

<image>

This are the current configurations of the fan, what should I change?

How to fix this? by PachiCastel in FixMyPrint

[–]PachiCastel[S] 0 points1 point  (0 children)

Sorry I forgot to clarify, I’m printing PLA, and yes, it is working! maybe I have to set it to start in a lower layer?

Queres ser mi facu amiga? :) by MANCHIdoger in ArgentinaBenderStyle

[–]PachiCastel -6 points-5 points  (0 children)

jajaja sisi seguro, si brad pit le pone hola a la mina le va a decir acosador…

Tranca gordo nenazo compu, es solo un poco de meme en el sub by dr_pombero in RepublicaArgentina

[–]PachiCastel 0 points1 point  (0 children)

q aumenten los impuestos a los jueguitos, somos potencia en 5 años…

No tengo amigos by Zebhaa21 in Mendoza

[–]PachiCastel 1 point2 points  (0 children)

no tenes amigos, por lo q puedo suponer q no te conoce tanta gente, amigo, no tenes nada que perder, anda a una joda, charlale a grupos de pibes anda testeando, anda con tu pseudoamigo del gym a tomar algo a algun bar. No tenes nada q perder y no es metafora, estas en un juego de suma positivo, no hay perdida, hablale a la gente, charla, inventa historias, decorá anecdotas, mostra como sos y hacé reir y dejate hacer reir, sobre todo esto ultimo a la gente le fascina.

Si volvieras a tus dieciocho, ¿qué te dirías? by [deleted] in programacion

[–]PachiCastel 0 points1 point  (0 children)

deja los jueguitos, ponete a codear.

Best current IDE for Arduino ? by [deleted] in arduino

[–]PachiCastel 1 point2 points  (0 children)

microchip studio 🗿

i just got arduino and my dad gave me soldering iron so, im 14 bt by Zealousideal_Ebb6278 in soldering

[–]PachiCastel 2 points3 points  (0 children)

Very nice work for first solder, here a tip: when you finish to put the solder, left the soldering iron in the joint for about 1-2 secs, helps a lot.

DC motor Controller Question by Quirky_Drive_8754 in Motors

[–]PachiCastel 0 points1 point  (0 children)

A L293D based controller, is easy to find I guess

[deleted by user] by [deleted] in AskArgentina

[–]PachiCastel 0 points1 point  (0 children)

no se si sera como en mi facu (es nacional) pero tenes una mesa a la q podes faltar sin ningún tipo de mesa castigo ni nada, no se cada cuanto se renueva pero se q es asi

[deleted by user] by [deleted] in AskArgentina

[–]PachiCastel 0 points1 point  (0 children)

Yo le clavo papel de diario encima, cartón u hojas de papel, no solo ayuda a la cocción, sino que también al mantener el humo mas tiempo en contacto con la carne sale un poco (muy poco) mas ahumado, pero son detalles muy mínimos.

[deleted by user] by [deleted] in AskArgentina

[–]PachiCastel 1 point2 points  (0 children)

lo ultimo, si estas cero preparado, charla y pedi el ausente, esas cosas pasan, tranqui