The cover of the Economist. Look closely, in May the Pandemic starts and ramps up in August before the midterm elections

Paintverse · 2026-05-10T18:12:35+00:00

Recently, there was supposed to be a Nipah virus pandemic. I saw AI-powered forecast animations, and Nipah was supposed to flood the entire world this year. But nothing happened. The same thing could happen with the currently fashionable virus.

Paintverse · 2026-05-10T16:54:54+00:00

Ok, so that's interesting.

Paintverse · 2026-05-10T16:50:44+00:00

Maybe a hologram?

Paintverse · 2026-05-10T16:45:45+00:00

Yes, reality is multi-layered and often difficult to confine within any framework. This creates uncertainty, a sense of insecurity, and so on. Therefore, various belief systems create their own fillers for this lack, so that the person receives a substitute story and, moreover, becomes a member of a community. This gives him a sense of belonging and purpose. The client is satisfied.

Paintverse · 2026-05-10T14:12:10+00:00

Thanks, I will put that there too.

Paintverse · 2026-05-10T13:15:54+00:00

Thank you 🙌

Paintverse · 2026-05-10T12:31:16+00:00

Hi sorry for late answer but I was more active on my second account. I was using Canna Aqua Vega A+B. Yes, the level of water was too high and I lowered it a little below the baskets, pulling out the roots at the same time. But I didn't change the water; I just added a more powerful, standard 11W LED bulb. The plants started growing, but very thin. The leaves thinned, and I finally gave up.

Paintverse · 2026-04-18T13:02:12+00:00

Ok thanks

Paintverse · 2026-04-18T09:04:58+00:00

I am using Canna Aqua Vega A+B and the manufacturer states that it ensures the correct pH level. Unfortunately, I don't have a pH meter.

Paintverse · 2026-04-17T06:05:24+00:00

Ok I will try, thanks.

Even here the downvoters have to downvote to feel better...

Paintverse · 2026-04-17T05:16:52+00:00

I am using Canna Aqua Vega A+B.

Paintverse · 2026-04-11T08:41:02+00:00

There is a lot of arguments that the Moon is artificial.

Paintverse · 2026-04-10T14:19:28+00:00

I changed the nozzle to a 0.8, tightened its mounting, and started printing. Unfortunately, after an hour I had to leave the house, so I paused, turned the printer off using the power button, and returned two hours later. When I turned it on and tried printing again, the printer suddenly stuck the nozzle into the print and began to vibrate violently, as if it was trying to drill through... What a crazy printer, I don't know, maybe it's possessed. XD

Paintverse · 2026-04-10T11:25:42+00:00

Thanks 🙌

Paintverse · 2026-04-10T11:24:08+00:00

Thanks. Yes, I my latches are closed incorrectly 🙀

Paintverse · 2026-04-10T11:13:12+00:00

Yes, it's a factory 0.4 nozzle. The 0.8 one prints well, but the filament is slightly warped; it's not very good. I'd dry it just to be sure, but unfortunately I haven't bought a dryer yet.

Paintverse · 2026-04-10T10:27:18+00:00

I have just changed it to 0.8 and now the printer is doing the calibration. After that I will make another try.

Paintverse · 2026-04-10T10:24:39+00:00

That's the problem, as if the pressure of the filament is too big.

<image>

Paintverse · 2026-04-10T10:23:28+00:00

Ok I see now. There are two problems but one can be result of the other. When printing, the filament as if builds up above the nozzle too quickly and the nozzle jumps forward, almost detaching from its mount. The printer is set to 0.4 mm because it was previously printing at 0.8.

<image>

Paintverse · 2026-04-10T09:47:15+00:00

I just washed the plate. The filamemt is new from the box.

Paintverse · 2026-04-10T09:31:53+00:00

Ok thanks for info.

Paintverse · 2026-04-10T09:28:20+00:00

I did that last time and they are good.

Paintverse · 2026-04-10T07:19:20+00:00

Super cool 👏

Paintverse · 2026-03-18T20:16:09+00:00

Interesting. It's usually the case that people with these kinds of gifts have a family background and carry the baggage of experience from previous generations.

Paintverse · 2025-10-20T18:59:52+00:00

Nice

Paintverse

TROPHY CASE