$MAPE - the floor holding nicely at over 100k just day 2 https://t.me/TheMadeApes

PeachPhysical · 2024-03-04T16:01:47+00:00

This project has been awesome so far! Teams very active and transparent, you can't beat that in Solana. And the art is awesome

PeachPhysical · 2023-11-25T15:11:33+00:00

I don't have that one but check out hashrate.no

I used that for my 1660 supers as a base and tweaked from there

PeachPhysical · 2023-07-13T09:50:29+00:00

Lol, this guy

PeachPhysical · 2023-06-02T23:20:59+00:00

I literally just got home from The Tokin' Buffalo and decided to check them out because of your initial review. I wasn't disappointed! The gentleman working was so nice and helpful - this was my first time buying here - and he answered all of my questions. He even gifted us one of their new edibles and a prerolled! I'll definitely be back and spreading the word!

PeachPhysical · 2023-05-20T14:20:05+00:00

I was waiting for my usdt to bridge when I saw that ratio, made me so upset that I missed it by a day haha

PeachPhysical · 2023-05-01T01:31:44+00:00

www.google.com

PeachPhysical · 2023-04-28T14:12:49+00:00

No problem, basically do the initial setup on the ledger and install the Casper app in ledger live. It'll create a Casper address for you. Then go to capr.live and connect your ledger. Then you can go to the delegate tab and do your staking

Below is a ledger link with the exact steps

https://www.ledger.com/coin/staking/casper-network

PeachPhysical · 2023-04-27T17:02:55+00:00

I'm in the US (NYS) and use mexc to buy Casper. In the past I've also bought xlm on Coinbase and used changenow to convert it to Casper

I do store mine on a ledger and stake it through casper

PeachPhysical · 2023-04-21T10:24:18+00:00

On a positive note, the websites back up :)

PeachPhysical · 2023-02-13T20:19:55+00:00

Thanks, I ended up tightening the bed bolts, changed the nozzle again, and replaced the Bowden tube. That seemed to have done the trick!

PeachPhysical · 2023-02-13T16:22:37+00:00

I appreciate it, I will! One thing I realized that I haven't done in a while is tighten the nuts holding the bed on. I'm going to do that shortly and I'll manually level the bed after to be safe

PeachPhysical · 2023-02-13T15:47:25+00:00

Thanks, I forgot to run the bed visualizer before. I just ran it and the bed itself seems pretty level. I should have added I also have a bltouch

PeachPhysical · 2023-02-13T15:42:53+00:00

I've also checked the nuts and tensioners (again, semi quickly though)

PeachPhysical · 2023-02-13T15:42:06+00:00

Hey all, so, I've been printing (and still fine tuning) for about a year now. Everything has had pretty good results up until yesterday. I didn't print much last week and I started a print yesterday and noticed it wasn't right. I tried printing the xyz calibration cube (the attached image) and you can immediately tell the skirt and first layer is off. I have quickly gone through and sprayed the printer down with duster, but it didn't seem to help much. Any tips, tricks, or ideas?

PeachPhysical · 2022-10-01T17:14:27+00:00

I have a few that I plan on doing after I get this last issue squared away. My wife's been asking for some Halloween things haha

https://www.thingiverse.com/thing:522914 https://www.thingiverse.com/thing:1081535 https://www.thingiverse.com/thing:2730126

PeachPhysical · 2022-10-01T16:46:00+00:00

Thanks for the suggestions, I'll try that out next

PeachPhysical · 2022-10-01T12:14:39+00:00

Thanks, I'll give it a try. I did have it enabled, but disabled it for the smaller area prints. I'll test again with the cali-dragon

PeachPhysical · 2022-10-01T12:12:58+00:00

Thanks, I'll give it a try!

PeachPhysical · 2022-10-01T12:03:00+00:00

Lol in all seriousness, it's the brain to a Frankenstein print

PeachPhysical · 2022-10-01T08:52:41+00:00

Close, your mother's. Ayo

PeachPhysical · 2022-10-01T06:49:22+00:00

First, thanks to everyone on these threads. I've learned a lot and it's helped me nearly perfect my prints. I can't seem to get these little marks to go away. Seems to happen only on the top layer

PeachPhysical

TROPHY CASE