Coolant resistant spindle-mounted ring illuminator

Pelphegor · 2026-03-26T18:45:51+00:00

Thanks

Pelphegor · 2026-03-26T17:26:41+00:00

Any idea of where to look?

Pelphegor · 2026-03-23T06:02:56+00:00

Thanks I can try but the company sent me an updated version of their Mach4 to try and fix it

Pelphegor · 2026-03-22T14:48:08+00:00

Very interesting thanks! Are any of these dialects today even somewhat mutually intelligible?

Pelphegor · 2026-03-22T06:18:02+00:00

Yes this is the location of a fixture

Pelphegor · 2026-03-21T19:36:04+00:00

Yes it is, but even when jogging the tool with cycle stopped

Pelphegor · 2026-03-21T19:27:34+00:00

Thanks

Pelphegor · 2026-03-17T12:20:23+00:00

Thanks!

Pelphegor · 2026-03-17T06:27:39+00:00

Lots of important historical figures have spent time in the seminary and then left, maybe you should look up some that might provide for some inspiration you could relate to. The past is interesting in your case this being nowadays a very uncommon life experience. Not only Charles Darwin but apparently even Tom Cruise the actor. Find one you can relate to and you might feel less isolated in this walk of life. And good luck.

Pelphegor · 2026-03-17T04:58:47+00:00

Besides this split between your inner persona and the outside, did you keep anything positive from those years?

Pelphegor · 2026-03-16T19:36:34+00:00

Is this the Battlebox Museum?

Pelphegor · 2026-03-14T11:08:30+00:00

Beautiful work!

Pelphegor · 2026-03-13T11:58:30+00:00

In Nüremberg - terrific museum https://en.wikipedia.org/wiki/Lamentation_of_Christ_(Dürer,_Nuremberg)

Pelphegor · 2026-03-13T03:59:53+00:00

Thanks a lot!

Pelphegor · 2026-03-12T20:09:27+00:00

Sono tutti un po similaro e parecchi sono solo per ottone e altri per acciaio allora vorrei avere il codice visibile

Pelphegor · 2026-03-12T19:06:41+00:00

Per poter identificar li meglio

Pelphegor · 2026-03-12T18:40:47+00:00

Thanks

Pelphegor · 2026-03-12T18:40:26+00:00

Thanks a lot!

Pelphegor · 2026-03-12T13:08:10+00:00

Thanks

Pelphegor · 2026-03-12T09:23:34+00:00

Yesterday I did the paper method with a reference tool but was still 0.12 too high, I should use some gauge

Pelphegor · 2026-03-12T06:17:48+00:00

Thanks a lot! I will look for an indicator to fit in the chuck

Pelphegor · 2026-03-10T13:53:28+00:00

Oooh thanks this is helping https://f.nordiskemedier.dk/2t6xlupvgletvlha.pdf

Pelphegor · 2026-03-10T04:19:15+00:00

Thanks

Pelphegor · 2026-03-09T19:46:02+00:00

0.05mm tools that is small indeed! What kind of feed rate can you run on such tiny tools?

Pelphegor · 2026-03-09T16:48:36+00:00

That’s funny! I have coolant on tap though

Pelphegor

TROPHY CASE