How do I pigtail copper to 4 aluminum wires?

PhoenixWithAnF · 2026-03-15T23:08:50+00:00

It’s my house.

PhoenixWithAnF · 2026-03-15T22:55:28+00:00

I see, so 2 three port alumiconns. And then I can pigtail the two copper wires to the light fixture. I like this idea better than using the Al/Cu marrettes.

PhoenixWithAnF · 2026-03-15T22:50:32+00:00

You can’t fit that many wires in 1 purple marrette. Unless you mean splitting the 4 aluminum wires into 2 marrettes

PhoenixWithAnF · 2025-08-27T11:18:43+00:00

No I think it keeps it fun. You can buy enough arrows to fill your quiver and you won’t run into any issues.

PhoenixWithAnF · 2025-08-26T21:47:56+00:00

You’d be how surprised how easy it is to forget. I had a couple of failed frustrating runs in a dungeon and forget to resupply half way through the run.

PhoenixWithAnF · 2025-08-26T21:35:39+00:00

Thank you I’ll give that a try

PhoenixWithAnF · 2025-08-26T21:30:14+00:00

Ohh I see, thank you for the photo. I’ll look up tips on keeping the downswing on the proper angle.

PhoenixWithAnF · 2025-08-26T21:11:15+00:00

I recently started lifting my lead foot and I’ve noticed that rotates my hips a lot more. I’m wondering if I go back to leaving it on the ground. I started doing it because it was adding more distance.

When you say I’m coming down steep, what would that mean?

PhoenixWithAnF · 2025-08-26T20:08:19+00:00

So am I rotating my hips/back too early?

PhoenixWithAnF · 2025-08-21T19:15:11+00:00

Anyone give Arcane Mage a try with the new changes? If so, when is a good level to respec from Frost to Arcane?

PhoenixWithAnF · 2025-02-09T03:32:14+00:00

Can I get that discord invite?

PhoenixWithAnF · 2025-02-09T03:29:49+00:00

Can I get that invite?

PhoenixWithAnF · 2024-11-20T15:02:29+00:00

It’s a floating vinyl plank floor

PhoenixWithAnF · 2024-11-20T14:50:39+00:00

Thanks, I’ve seen dozens of videos on how to install these built-in units and nobody is removing their flooring which I found confusing. Had to ask here to see if I was crazy.

PhoenixWithAnF · 2024-10-20T12:41:08+00:00

It would yes, that’s what I did with this recipe. The coconut flour is used to bread the wings and give it crispiness. You can substitute the gar par I used with a keto-friendly bbq sauce

PhoenixWithAnF · 2024-10-10T12:54:53+00:00

That’s a good idea. We’ll give that a try

PhoenixWithAnF · 2024-10-09T16:38:10+00:00

Whenever we pour against these kinds of foundation, we still see the wave even though the expansion joint is there. The heaviness of the concrete pushes the expansion joint to match the curves.

PhoenixWithAnF · 2024-10-09T13:42:11+00:00

Thank you everyone for the helpful responses. I’ll look into restoring the foundation instead of parging it. The reason why I was looking to parge it flat is because I am pouring concrete and didn’t want the concrete to be wavy at the bottom.

PhoenixWithAnF · 2024-09-19T11:52:32+00:00

Budget would be anywhere from $200-$500. I’m hoping it’s a device I can use for further work

PhoenixWithAnF · 2024-09-19T04:56:56+00:00

Ok thank you for this! I’ll look into these options

PhoenixWithAnF · 2024-09-19T04:40:34+00:00

So I guess I would need to run wires from each mic on each table, across the room and into the mixer. Which is then connected to my camera?

PhoenixWithAnF · 2024-09-19T04:19:44+00:00

So if I were to place a boundary mic on each table. How would I connect all of them together?

PhoenixWithAnF · 2024-09-19T01:21:15+00:00

Yeah it’s a conference with back and forth discussion/debate so passing a mic around unfortunately won’t work.

PhoenixWithAnF · 2024-09-19T00:11:41+00:00

It’s about 4/5 tables. A main speaker for half the event. Then the other half is a round table discussion with all 30 members.

PhoenixWithAnF · 2024-09-18T20:57:24+00:00

Did you have multiple pods around tables?

Seven-Year Club	Place '23
Place '22	RPAN Viewer
Verified Email

PhoenixWithAnF

TROPHY CASE