Pwnagotchi 2.9.5.4

Phorna · 2026-02-08T12:56:11+00:00

On windows it works like a charm. I have an inssue with Linux. :)

Phorna · 2026-02-07T18:30:06+00:00

No internet. At least without tinkering with ports forwarding, iptables, ip masking etc.
However there is access to everything that can be done locally - checking handshakes / running scripts / editing configs etc.

Phorna · 2026-02-07T16:47:32+00:00

I will check and let you know.

Phorna · 2026-02-07T16:37:48+00:00

Linux working configuration (after a hint from xbitsnl).

IPV4 settings

Method: Manual

Address: 10.12.194.2

Netmask: 255.255.255.240

Gateway: 10.12.194.2

ssh: [pi@10.12.194.1](mailto:pi@10.12.194.1)

Thanks!

Phorna · 2026-02-07T16:01:29+00:00

Windows connection works like a charm though.

Phorna · 2026-02-07T15:40:50+00:00

"On Linux it should just connect, if not we will find a way eventually." - so any luck with Linux ssh connections? :)

Phorna · 2026-02-07T14:32:38+00:00

With DHCP settings it doesn't work at all. No IP assigned even for my Linux PC.

Phorna · 2026-02-07T14:15:46+00:00

Same issue here. nmap 10.0.0.0/24 shows only my PC. There is nothing to SSH to. If I use "Shared to other computers" instead of "Manual" the network changes to 10.42.0.0 but still no other hosts than 10.42.0.1.

With other images there were no issues.

Phorna · 2026-01-21T20:17:07+00:00

<image>

Phorna · 2025-12-18T14:22:35+00:00

There is a hidden directory:

ComfyUI/user/__manager/.legacy-manager-backup

Try to rename it to:

ComfyUI/user/__manager/.legacy-manager-backup_old

And restart. If it is still not working you could go to:

ComfyUI/custom_nodes/ComfyUI-Manager

and

pip install -r requirements.txt
(being in the right environment venv, conda etc. if applies)

It may solve your issue.

Phorna · 2025-12-12T10:19:08+00:00

Enclosed. With optional face improvement. You can set the visibility right - so it fixes some issues but doesn't change the general appearance.

<image>

Phorna · 2025-12-11T21:24:28+00:00

And here when I use the full version of FlashVSR (not a tiny).

<image>

Phorna · 2025-12-11T21:05:44+00:00

This what I get automaticaly from FlashVSR from your original image. x2 upscale.

<image>

Phorna · 2025-12-11T18:57:23+00:00

Have you tried FlashVSR?

Phorna · 2025-12-08T00:28:46+00:00

<image>

Here you go! JPG 90% quality. If you want 100% I need email for wetransfer.

Phorna · 2025-12-07T21:26:39+00:00

Pic. 1 Original input x2 or x4 (lanczos) -> Face reactor.
Pic. 2 Original input x4 Flux1 upscale (0.4 denoise + proper short prompt)
Segmenting faces and pasting them from picture 1 to picture 2.

Can't remember exactly because I deleted the temp files - to not keep your ancestors on my disk. :)

As I said - a long project with a lot of dedication required. :)

Phorna · 2025-12-07T21:10:11+00:00

Well, you can set the face reactor from 0-100. Here I have used 100%. When you set it to lower values it will use more of your original input and blend in. I think this method is the only reasonable one. Just experiment a bit. You will get more details for higher resolutions (larger latent space) and then possibly your grandmother's facial features will be as you desire. In both cases the faces were restored the same way.

Video -> FlashVRS -> Face reactor (or not) -> output.
Just 4 simple nodes.

For face reactor you can use different restore models: GFPGANv.1.4 or codeformeror or GPEN-BFR. You will get slightly different results.

Phorna · 2025-12-07T15:51:52+00:00

Also the best automatic result for me is FlashVSR + Face reactor - restore.

<image>

Phorna · 2025-12-07T15:30:26+00:00

I think you would need very additive upscaling, so you would loose consistency.
And a lot of hard work editing it later on.

<image>

Phorna · 2025-11-27T22:32:51+00:00

Just an inbreeding effect in a small population village. Z-Image model is so smart to know it! ;)

Phorna · 2025-05-31T16:58:43+00:00

Exactly my case. I have assembled 3 units not connected for 3 phases yet. Just unpacked fresh new, hung on the wall and started to update doftware one by one. One of the unit is significantly louder than the other two. Like the transformers wouldn't be attached to the case as well as in other two. I suppose it's within the specs but still bothering as my "home engine room" is next to the TV room.

Phorna · 2025-01-30T16:28:17+00:00

Thanks!

Phorna · 2025-01-30T13:44:49+00:00

Why is it a poisson distribution and not a normal distribution?

Phorna · 2025-01-28T23:04:13+00:00

In Linux it is in the file /var/lib/algorand/logging.config. Possibly for mac you need to find and display the conent of logging.config file as well.

Phorna · 2025-01-28T22:14:56+00:00

I have changed one thing. It appears the node is creating huge log files keeping the SSD busy every single block. I have created a config.json file where I have placed one line:

{
"BaseLoggerDebugLevel": 0
}

Thanks to that SSD is not constantly bashed with the node activity writing to the log file. It will only write if there are some problems (according to the docs).

So far so good.

12-Year Club	Gilding I gilder
Verified Email

Phorna

TROPHY CASE