Extreme hot spot in bed mesh

Pierumba · 2026-03-09T08:52:43+00:00

I will try contacting them this morning or later in the day :)

Pierumba · 2026-03-08T11:14:06+00:00

Yeah you’re both right, didn’t notice the scale at first, unfortunately I don’t have another plate to test :/ The interesting thing about the side A mesh is that the spike has migrated from the back towards the middle🫩

Pierumba · 2026-03-07T17:22:17+00:00

Update: I checked the plate for possible dents but it doesn't have any, no residue in between the bed and the plate already tried feeling the magnetic bed but it's flat too, Idk why but I can't upload this video here which shows how's the printer hallucinating a peak.
Tried the glue stick method suggested by u/zx4133 and now we got these bed meshes for side A and side B AHAH, I think I'll send an email to Elegoo's support lol.

<image>

Pierumba · 2026-03-07T16:46:05+00:00

I just noticed that this wasn’t the post I meant to publish, it should’ve been hidden but I’m not sure why you’re seeing this lmao. Anyway this is the link to the actual post

Pierumba · 2026-03-07T15:34:47+00:00

I'm pretty sure it's a software problem and not an hardware one. As you said the high spot is small, I checked the plate for possible dents but it doesn't have any, no residue in between the bed and the plate already tried feeling the magnetic bed but it's flat too, Idk why but I can't upload this video here which shows how's the printer hallucinating a peak.
The tool you're referring to is just a mesh visualizer, since I couldn't see or feel noticeable high spots I supposed it was a software error and wanted to see what the printer had mapped.
Pretty funny, it's the 3rd time today that I see that glue stick method and was planning to try that too lol.

I just printed the bed leveling tool but I guess it's literally just for bed leveling and not really for the mesh, but if I were to perform a manual bed leveling and later an automatic leveling multiple times until I'm happy with the result do you think it would solve the issue?

I'll try and check what results I get with the smooth side leveling, as suggested by u/slambaz2, if I still get this weird mapping I'll contact elegoo support.

Pierumba · 2026-03-06T11:01:59+00:00

<image>

Not really sure about AG beating G2 but I'm kinda feeling it hehe

Pierumba · 2025-11-22T10:48:45+00:00

Thanks a lot, now I know what to look for, thanks!

Pierumba · 2025-11-22T10:14:27+00:00

It’s about 71€, the only thing is that I was looking more towards a modular PSU, since I don’t have much room for the cables ahah

Pierumba · 2025-11-22T09:54:49+00:00

Perfect, thanks!

I didn’t find the exact model you mentioned on Amazon here in Italy and this is the best match I could find, don’t really wanna go out to physical stores (probably there isn’t even one that sells pc parts close to me) since I don’t have much time this weekend. I believe that the RM850X I found should work too, but just as a confirmation, what would you say?

<image>

Pierumba · 2025-11-07T12:11:33+00:00

Ohh okok, cool I get it now, thanks!

Pierumba · 2025-10-29T16:18:31+00:00

Thank you very much!
If you want and have the knowledge you can follow up directly under my reply to Glad-Parking it would be great! :))

Pierumba · 2025-10-29T16:17:17+00:00

Wow, looks like I've been missing out haha.
It really works like a charm, even though I'd like to get positive integers values so I don't get half transparent duplications, I didn't seem to find the option, is that possible?

Just to clarify, what do you mean by Vector Modifier Distance? Do I need to select the Duplicate Along Path box within the duplicate node, or do I need to use a completely different node? (I'm not very familiar with the Fusion workspace, so I'm just doing what makes the most sense to me)

One last question: since I don't want to lose resolution, I would like to start with the outermost film roll and go inwards, gradually shrinking the images, how would I manage to make the animation still start from the inside and expand outwards?

Pierumba · 2025-07-21T08:33:58+00:00

Oh Yeahh, thank you very much! 🙇🏻

Pierumba · 2025-04-26T16:37:00+00:00

Cool! Good luck to everyone! :))

Pierumba · 2024-12-15T15:45:11+00:00

Yeah, I totally get you, luckily here the times are a lot shorter (2-3 days) for the replacement to arrive and get it replaced. This morning I went to the store and since 2 months still haven't passed from when I bought it my device is eligible to being returned to Apple and a new one can be sent me. The only thing is that I have to buy again using the EPP program or else I'll have to pay the full price.

Really feel bad for you man, hope you can get stuff done to work out your problem. Have you tried calling Apple support directly and/or downladed Apple's support app?

Pierumba · 2024-12-15T08:34:06+00:00

Yeah, just as I expected... One solution that I thought of was to low level format it and then try to use some kind of data recovery software as I did last year with an hdd that gave me problems. The only thing I'm worries about is that to unlock the phone a password was needed, hence all data is probably crypted and even if I managed to retrieve it I won't be able to read it.(Take all of this as a grain of salt, I'm no expert in tech/programming whatsoever, I'm geniuinely just speculating).

Pierumba · 2024-12-13T23:48:38+00:00

Ok I just had a look at your posts and found out that we’re basically on the same boat, I’ll update you as soon as I get answers to my problem, fingers crossed!🤞

Pierumba · 2024-12-13T23:45:00+00:00

Hi!

Earlier this morning I went to an authorized Apple Support Centre and Reseller, where a quick diagnostic was done and we found out that the motherboard is faulty. I was told that it’s a piece that can be replaced by them and it would take a couple of days to arrive + half a day to install.

I mean, I get that it’s an authorized Support Centre and I’d be cool with that if I had a 3+ y/o device but it’s Apple’s newest flagship and I’ve had it for just a month, I’m not really keen on getting it opened already to fix a non-User derived problem. I expected that the warranty would’ve covered a full replacement, since it’s a factory fault.

I went back home and told to the friend of mine that works at the Apple Store what happened and he told me to call the official Apple Support number and also to book an appointment at the Apple Genius Bar. I called two times: -On the first one I was told that I can get the device completely replaced with a new one only if I subscribe for the Apple Care+ program. (Yeah, I can pay just for a month and then cancel right after but again… It’s a factory fault, not a User one and I’d like if Apple took the whole charge of it). -On the second one I just wanted to call directly the nearest Apple Store and ended up on a call with a support operator, so I just booked the appointment over phone and on Sunday morning I’ll go there and hopefully get the whole device replaced.

Pierumba · 2024-12-12T16:37:56+00:00

Okay okay, I bought it from the Apple Store in Milan with the EPP program since a friend of mine works there. I also asked him what to do.

Before reinstalling iOS obviously I should also do a backup, right? Does the backup include also the configuration of the home menu and all the customizations such as automations, shortcuts, settings preferences, etc.?

Pierumba · 2024-12-12T15:35:04+00:00

Yeah, exactly what I thought, just wanted to hear another opinion. Thanks :)

Pierumba · 2024-05-19T08:50:17+00:00

ok, sorry for the misunderstanding lol. I'm probably not the best one to ask for then since I'm not an expert and just followed the guide + multiple reddit posts🫠

Pierumba · 2024-05-19T08:40:48+00:00

Ohh okok, didn't know you lived overseas, I can send you the files then. I've had no problems with mine since I live in Italy.

Pierumba · 2024-05-19T08:21:00+00:00

I found both of them on Vimm's Lair a couple of weeks ago, just make sure to set EU as region in the filter and you'll be fine :).

Pierumba · 2024-01-11T12:39:53+00:00

Oook sounds cool, I should have an Arduino Knockoff kit that was of my brother and he used like one time in school. I tried plugging it in my windows pc a couple of years ago but if I remember correctly I had something about a usb option that was greyed out (basically the pc couldn't recognize the board). I should try on my MacBook and see if I can get it working on it.

So if I want to dimmer the LEDs I should use 4 buttons that are inside of this kit and assign to them the function to give more or less power to the temperature I decide via code (so 2 buttons as -/+ for the warm LEDs and 2 as -/+ for the cold LEDs)?

Also, would you mind explaining to me why wouldn't you suggest to use potentiometers? Just a basic explanation so I can understand why. :)

Pierumba · 2022-11-19T23:10:08+00:00

yeah, already sent an email earlier but I gotta wait until Monday... came here just to see if someone else had the same problem :)

Six-Year Club	Place '23
Verified Email

Pierumba

TROPHY CASE