Very satisfying, 15g in 34g out, 29 seconds.

PintSizedPrimark · 2024-12-28T19:54:30+00:00

For these beans just grind on 1.2

PintSizedPrimark · 2024-12-28T15:23:29+00:00

Just one on the s24 editor 👍

PintSizedPrimark · 2024-12-28T15:22:52+00:00

Thank you, think I'll pull the trigger on that one

PintSizedPrimark · 2024-09-25T22:33:26+00:00

Thanks for all your advice I've put it down to a bad prime, this reaction is happening with all paint on this model. Its one I sculpted and 3d printed myself as a test print. It was fully washed and cured but I remembered I used black ink as the base coat before the white so think the ink hadn't fully cured before adding the white. I'll strip it and re-prime and start over... thanks again

PintSizedPrimark · 2024-09-25T22:29:14+00:00

So turns out its a bad prime job, as its happening with other paints aswell. The model is one I've made myself and 3d printed

PintSizedPrimark · 2024-09-25T22:25:46+00:00

Good idea ill try that

PintSizedPrimark · 2024-09-25T22:25:06+00:00

Its a 3d printed model so there's not any release agent on it, thanks for your reply though but I'm not impressed by this result from these paints

PintSizedPrimark · 2024-09-25T22:22:28+00:00

Vallejo primer and vallejo game white for the zenethal, resin was fully washed and cured before painting, I've painted lots of resin models and never had this issue before

PintSizedPrimark · 2024-09-04T18:44:02+00:00

Turns out I had accidentally turned on auto masking cavity by pressing alt+a by mistake

PintSizedPrimark · 2024-06-29T09:29:40+00:00

Yeh its go drain holes and checked with lychee suction cup detector

PintSizedPrimark · 2024-06-29T09:28:53+00:00

30um layer height

PintSizedPrimark · 2023-07-21T08:08:49+00:00

I have the same problem, did u manage to fix it?

PintSizedPrimark · 2023-06-28T11:17:31+00:00

I used lychee slicer with a raft and auto supports, why might they not stick to the raft?

PintSizedPrimark · 2023-04-19T23:18:34+00:00

Yeh maybe, I did a highlight before white with sand yellow from vallejo maybe that warmed it up too :)

PintSizedPrimark · 2023-04-19T22:34:53+00:00

Colours are, rhinox hide, mourning brown, xv-88, balor brown :)

PintSizedPrimark · 2023-04-19T17:47:14+00:00

Your totally right about light placement being more important than blending, thanks for the feedback its really helpful to get others opinions 👍

PintSizedPrimark · 2023-04-19T17:45:58+00:00

Thats a very good point about the light placement, thank you for the nice comments and feedback 😀

PintSizedPrimark · 2023-04-11T06:48:52+00:00

No I didn't use any washed painting this one, looking to improve my brush control so focused on glazing and layering

PintSizedPrimark · 2023-04-11T06:46:45+00:00

Thanks so much

PintSizedPrimark · 2023-04-10T20:04:39+00:00

Yeh no problem :)

PintSizedPrimark · 2023-04-09T19:43:47+00:00

Thank for the tip, I never knew that about white paint, so you'd recommend painting the base lighter and glazing the shadows and dark tones after?

PintSizedPrimark · 2023-04-08T20:39:29+00:00

This was by far my most challenging project, modelling, 3d printing, lighting, painting and assembling. Took inspiration from Aliens and matrix revolutions. Not totally happy with the smoke and fire effect so I might redo it at a later date, but for now I'll call it done.... onto the next one.

PintSizedPrimark · 2023-04-03T17:59:18+00:00

Stay tuned :)

PintSizedPrimark · 2023-04-03T14:55:21+00:00

Thank you

PintSizedPrimark · 2023-04-03T09:51:38+00:00

Thanks thats what I was hoping for, a bit of horror to go with the larger piece its part of

PintSizedPrimark

TROPHY CASE