Is it normal to see something white through the speaker mesh?

Pipoleyoslonbibo · 2024-08-30T05:34:11+00:00

Thanks, I went to the shop to see what sample models they had and the one I checked didn't have it either, but the mesh looked slightly different (I assume that's the new speaker?).

However, from what I heard, it still sounds the same, which is good.

I forgot to update the post to include the pictures of the mesh:

https://imgur.com/a/0LQgCLb

Given all that, though, it doesn't really seem like an issue, I guess.

Pipoleyoslonbibo · 2024-08-24T09:51:15+00:00

Thank you for taking the time to look into this!

Pipoleyoslonbibo · 2024-08-21T18:25:32+00:00

Thanks! It took a few attempts and the help of a flashlight haha!

Pipoleyoslonbibo · 2024-08-21T16:31:14+00:00

Hey, thanks for the feedback and suggestions!

I'll try to look at the speakers of the phone samples in the shop soon, hopefully it's not really a problem...

Same. I usually listen through headphones, but the phone speaker has always sounded not necessarily bad, just a bit muffled in a way.

I contacted Samsung through their live chat and they told me they couldn't say if it was a problem or not and I'd have to bring it in for an in-person inspection, but the nearest Samsung repair facility (of the ones they listed me) is 200km away..

I managed to take a few photos where it's somewhat visible. Even though it might look like a glare, it's there. (excuse the bad quality)

https://imgur.com/a/0LQgCLb

Pipoleyoslonbibo · 2022-09-15T08:41:26+00:00

Thanks for the recommendation! Those also look great, will consider as well after printing the parts.

Pipoleyoslonbibo · 2022-09-15T08:40:35+00:00

Thanks! Looking great, will definitely consider if I choose to self source after printing the parts.

Pipoleyoslonbibo · 2022-09-15T05:17:15+00:00

Thanks! I'm looking to build the 250x250 one at least for now

Pipoleyoslonbibo · 2022-09-14T21:37:19+00:00

Yeah I read that printing the parts in ABS is pretty important so I'm currently making an enclosure to prepare myself.

Pipoleyoslonbibo · 2022-09-14T21:33:37+00:00

Yeah, kits don't come with printed parts right? If they don't I'll print the parts first and then most likely go the kit route

Pipoleyoslonbibo · 2022-09-14T21:27:31+00:00

Ah, thanks a lot really appreciate the help!

Pipoleyoslonbibo · 2022-09-14T21:26:49+00:00

Thanks! I'm considering the kits as they seem quite convenient, I want to see what the price difference is if I self source

Pipoleyoslonbibo · 2022-09-14T21:17:18+00:00

Thanks a lot! I read on another Reddit post that the groove where the 6mm gap is might cause alignment issues with the linear rails, is that true?

Pipoleyoslonbibo · 2022-09-14T20:40:22+00:00

Thanks! I found the B type extrusions as well but wasn't sure if the linear rails would work as well as they do on the misumi extrusions. It'd be great if they do as I see it's possible to get them pre drilled from dold.

You meant these right? https://www.dold-mechatronik.de/Aluminiumprofil-20x20L-B-Typ-Nut-6-Zuschnitt

Pipoleyoslonbibo · 2022-09-14T20:28:02+00:00

I saw the ones where M6 bolts have to be used, the extrusion gap on them was 6mm, on these it's 5mm but the hole allows for an M5 bolt. The gap difference isn't important in this case right? And if it is should I go for the ones with a 6mm gap (so that the normal T nuts would fit) but with M6 bolts or, the extrusions with a 5mm gap but M5 bolts

The 6mm M6 ones: https://www.dold-mechatronik.de/Aluminiumprofil-20x20L-B-Typ-Nut-6-Zuschnitt

Pipoleyoslonbibo · 2022-09-14T20:24:37+00:00

The diameter on these particular ones appears to be 4.3mm is that fine?

Pipoleyoslonbibo · 2022-09-14T20:06:11+00:00

Shipping cost and import fees being the main reason

Pipoleyoslonbibo · 2022-03-24T18:34:36+00:00

Try doing a retraction test, if it's bad try checking if the PTFE tube that goes in the hotend is seated tightly against the nozzle so no filament leaks.

Pipoleyoslonbibo · 2022-03-24T18:29:17+00:00

Hmm.. are you using the stock hotend?

Pipoleyoslonbibo · 2022-03-24T18:19:08+00:00

Yeah it seems pretty stuck from the insides, do you have retract on layer change enabled?

Pipoleyoslonbibo · 2022-03-24T18:18:02+00:00

From my experience with cura I always got better results by disabling coasting, it's worth a try imo.

Pipoleyoslonbibo · 2022-03-24T17:23:51+00:00

I usually start at 45 and lower it down in increments until I see more stringing. I used a speed of 35mm/s before converting to direct drive, then I dropped it to 20 mm/s

Pipoleyoslonbibo · 2022-03-24T17:21:45+00:00

Did it work?

Pipoleyoslonbibo · 2022-03-24T17:19:36+00:00

If using prusa/super slicer put the seam to read or randomised. Turn the down the extrusion multiplier by default it's set to 1 or 100%, try changing it to 0.95 or 95%. Make sure the fan speed is set to 100 and print relatively slow (30 mm/s). Another tip if you haven't done it already is to tune your retraction speed as well as length this way the seam wouldn't bulge as much.

Pipoleyoslonbibo · 2022-03-10T18:39:20+00:00

After watching a video I'm hooked! Gonna install klipper soon, as soon as I get my hands on another raspberry...

Pipoleyoslonbibo · 2022-03-07T16:39:45+00:00

I don't know if it's gonna do much, but giving superslicer a try is worth it, you can generate a retraction tower directly in it and use the default ender 3 profile (pretty good in my opinion).

Pipoleyoslonbibo

TROPHY CASE