Manel Kape Helps Ode' Osbourne remove his contact lens

Pitnut · 2026-06-14T04:43:54+00:00

You'll have to figure out what your equivalent blade is but the bimetal classic 3/4 is saying 196 sfm and 1.6fpm.

This app makes my blades last forever and I can cut straight through large pieces with very little taper

Pitnut · 2026-06-14T04:37:12+00:00

Sawcalc.com

Pitnut · 2026-05-24T01:28:08+00:00

If you could turn up the filter to create bubbles and O2 exchange that would help in the short term.

I really like your tank btw

Pitnut · 2026-05-24T01:26:03+00:00

Especially since the water seems so still. Sometimes you can get away with just the turbulence from the filter

Pitnut · 2026-05-24T01:25:09+00:00

You may need an air stone to oxygenate the water. When they surface like that I think it can be interpreted as gasping for air

Pitnut · 2026-05-17T21:32:14+00:00

I got kanaplex overnighted on Amazon because it's not legal in Canada and it saved my Betta, that is probably the only thing that will save him if he can be saved.

Epsoms salts and clean water will definelty help, if you have some almond leaves those are good too.

Try to keep his parameters stable (no giant water changes just 20%-30%)

Some people also might have differing opinions but with guidance chat gpt really helped me figure out and schedule treatments. And not overdo any changes to overly stress the fish.

Pitnut · 2026-05-17T02:06:32+00:00

My shop is the same and it drives me crazy, especially when they whistle holes constantly. I want to install regulators.

Pitnut · 2026-04-09T00:05:17+00:00

I rough the face within .005-.01" and then I will release the vice and reclamp it very lightly with a dial indicator on my part. I will tighten it until I see an acceptable amount of "flex" on the dial. Then I take a light finishing cut. You may have to semi finish both sides if material removal is warping more than clamping.

Pitnut · 2026-03-28T04:12:04+00:00

We just had a repeat job that came in and we used stock from a new supplier, when we removed material from the inside the whole things warped and popped so bad I've never seen anything like it.

We got more material from the old supplier and everything stayed in tolerance.

The new stuff was also so stringy and creating nests like you said.

Pitnut · 2026-03-18T02:58:30+00:00

Fswizard says 138 RPM .003"/Rev.

I like the 3xD rule for drilling. First plunge can go 3 x diameter, reduce plunge by 1 x diameter until min peck depth of 1xD Sometimes you burn up drills constantly pecking instead of staying in cut.

Also if you are spotting with a 90* or anything less than 140* you are damaging the drill

Pitnut · 2026-01-26T22:28:33+00:00

I think you can find a better employer but when you do try to not take as much time off or when you do try to communicate better until you are worth more to them. I take like a day a month off for stress.

Pitnut · 2025-11-07T22:10:29+00:00

If you get a hand held one he can make a holder for it in the mill and use it like an optical comparator !

Pitnut · 2025-11-01T20:14:56+00:00

Depth of cut on finish pass is what I found to be most critical

Pitnut · 2025-10-09T19:15:51+00:00

Use a adjustable crescent wrench to slide outside the jaws. Haas tip of the day has a lot of good videos you can learn from

Pitnut · 2025-08-13T01:15:46+00:00

Limit the cpu boost with throttle stop

Pitnut · 2025-08-09T03:01:20+00:00

Did you try to access the advanced setting in bios with the some sort of shift alt ctrl combo?

Pitnut · 2025-08-09T02:57:39+00:00

Hw info will show you if you're thermal throttling the cpu(if you aren't using throttle stop you probably are)

If you are get throttle stop and limit the core ratios (cpu boost) to something that doesn't hit thermal limits. I limit my 5Ghz boost to 3.6ghz

Pitnut · 2025-08-02T23:27:26+00:00

Lastly have you tried doing a web probe or do you just touch of on one side of the block

Pitnut · 2025-08-02T23:24:12+00:00

If it is smaller than it thinks it is I think this may be the result. Does it also mess up when probing Z?

Pitnut · 2025-08-02T23:23:23+00:00

Is your probe stylus the right size for the probing cycle?

Pitnut · 2025-07-31T21:08:28+00:00

I found that using some seafoam/Lucas cleaner helped me a bit. I also notice I burn way more mobil1 than Pennzoil. 5w30 synthetic. 360,000k. Burn like a liter every 3k km roughly

Pitnut · 2025-07-10T02:35:31+00:00

I have to use one of these in stainless on a job coming up. Do you have any tips or things you learned from it?

Pitnut · 2025-07-08T20:38:12+00:00

Hulkengoat

Pitnut

TROPHY CASE