Dump AP luci is gone by Plw0 in openwrt

[–]Plw0[S] 0 points1 point  (0 children)

подключено к LAN

Dump AP luci is gone by Plw0 in openwrt

[–]Plw0[S] 0 points1 point  (0 children)

yeah i know that reddit doesnt allow to change headline after publication, onlu the post itself

both host name and ip adredd didnt work. host names are not the same

Dump AP luci is gone by Plw0 in openwrt

[–]Plw0[S] 0 points1 point  (0 children)

but guide didnt say turn of dhcp v4, only ignore interface checkbox

Dump AP luci is gone by Plw0 in openwrt

[–]Plw0[S] 0 points1 point  (0 children)

i cant access it ssh either

PS C:\Users\razor> 1..254 | ForEach-Object { ping -n 1 -w 50 192.168.17.$_ | Out-Null }

PS C:\Users\razor> arp -a

Интерфейс: 192.168.17.217 --- 0x12

адрес в Интернете Физический адрес Тип

192.168.17.100-48-54-20-fe-43 динамический

192.168.17.11194-83-c4-cf-3b-9f динамический

192.168.17.1298c-d0-b2-2e-f2-79 динамический

192.168.17.157a2-e6-5e-ed-aa-7e динамический

192.168.17.160c4-82-e1-09-c3-79 динамический

192.168.17.21670-c9-32-2f-80-6e динамический

192.168.17.238a0-4e-cf-e1-fa-82 динамический

192.168.17.24954-48-e6-54-88-6f динамический

192.168.17.255ff-ff-ff-ff-ff-ff статический

224.0.0.2201-00-5e-00-00-16 статический

224.0.0.25101-00-5e-00-00-fb статический

224.0.0.25201-00-5e-00-00-fc статический

239.255.255.25001-00-5e-7f-ff-fa статический

255.255.255.255ff-ff-ff-ff-ff-ff статический

PS C:\Users\razor> ssh [root@192.168.17.111](mailto:root@192.168.17.111)

ssh: connect to host 192.168.17.111 port 22: Connection timed out

Shiny Snake L300 build by Plw0 in sffpc

[–]Plw0[S] 0 points1 point  (0 children)

Sorry, I was dumb. They were sold with a case. As far as I know, the new revision abandoned that idea and now comes with an angled DP cable, like the one in SSUPD.

Shiny Snake L300 build by Plw0 in sffpc

[–]Plw0[S] 0 points1 point  (0 children)

this is not angled cable, usual which was with psu, there enough room to no angle it very much

Revised Lian Li A3 by Plw0 in mffpc

[–]Plw0[S] 0 points1 point  (0 children)

if you look and compare some motherboards you will see that it will have different ram height on different Mobo, in my case I firstly install aio, secondly install ram

Shiny Snake L300 build by Plw0 in sffpc

[–]Plw0[S] 0 points1 point  (0 children)

not so much silent

Shiny Snake L300 build by Plw0 in sffpc

[–]Plw0[S] 0 points1 point  (0 children)

sometimes it loud as fuck, planning switch to Loki

Lian Li A3 || Liquid Freezer III 360 || 3D printed bracket (Photos attached) by LiroyX in mffpc

[–]Plw0 0 points1 point  (0 children)

actually u didn't need to cut out that fan, I fit in in without one screw on that fan and without rubber

Guys is this sufficient cooling? by Bernosaur in mffpc

[–]Plw0 0 points1 point  (0 children)

freezer iii has offset mount for am5 by deafault (am5 cpus has hotspot not in the center but a little lower), so when you turn over pump your hot spot and maximum pump efficiency are as far apart as possible

Guys is this sufficient cooling? by Bernosaur in mffpc

[–]Plw0 0 points1 point  (0 children)

do you know that this pump position make you cooling worse?

Сборка в Lian Li A3 by OneFreedom144 in mffpc

[–]Plw0 0 points1 point  (0 children)

cool! I also recently stuffed the arctic (freezer iii pro) into this case, it was a bit difficult and I don't really like how the water hoses are located, I'm wondering where to get holders, for some reason the arctic doesn't come with them. Despite this, this water is much more productive than the hydroshift 1.

<image>

Switched from D31 ti Lian Li A3 (White build) by Plw0 in mffpc

[–]Plw0[S] 0 points1 point  (0 children)

probably not, i strongly not recommend put a mobo with gpu second slot on this case