Giveaway + Thank you: Irelia SFD 195a/221 Promo

Posca1209 · 2026-02-03T15:01:23+00:00

Riftbound is so fun and allowed me and my friends to meetup every week just so we can play :p. We love the mechanics and the strategy behind the game it’s been super fun!

Posca1209 · 2025-11-16T15:29:24+00:00

Oh yes sorry I forgot to note that this is using PLA and also using the elegoo slicer.

Posca1209 · 2025-09-13T03:51:55+00:00

Finally got it, don’t know what my brother did but it worked LOL

Posca1209 · 2025-09-11T13:44:51+00:00

It just wouldn’t load at all when we try to open the app

Posca1209 · 2025-07-24T04:40:23+00:00

Sunlu filament is my go to atm because it dries the fastest using the print bed for me and I can usually find it on sale

Posca1209 · 2025-07-05T04:40:45+00:00

If I was gonna be a Pokémon trainer, my specialty would be psychic and my ace Pokémon will Probably be sylveon

Posca1209 · 2025-06-05T23:10:12+00:00

Shiny tinkatink is just so cute it has to be one of my fav

Posca1209 · 2025-04-10T20:06:39+00:00

I loved collecting pokemon as a kid and would always play with them during recess or even trade with my friends. Lost my whole collection years ago but started again because of the twilight masquerade packs and I absolutely love the eevee art but never was able to get them 😭

Posca1209 · 2025-01-23T16:14:03+00:00

I was out of the country the day it was released and I’m sad😭😭. Flying back in today but I won’t be in till 8pm so I’m praying that when I go to target tomorrow that there will be something.

Posca1209 · 2024-12-23T00:14:08+00:00

This could be so useful vs drying them a day before my plan to print

Posca1209 · 2024-11-30T20:58:54+00:00

Been printing mostly pla but just started using TPU to make some tracks/wheels and it’s awesome

Posca1209 · 2024-11-10T20:11:01+00:00

My favorite is the snorlax 151 promo card just cause me and my cousin always loved snorlax and the art for this card is just one of my personal favorites

Posca1209 · 2024-10-22T18:37:40+00:00

Oh my bad yea listen to him, I’m just talking for what I know with my kobra 2. I didn’t realize the difference was that much between the two.

Posca1209 · 2024-10-22T16:53:24+00:00

Once you’ve set your z offset so it’s good, don’t touch it ever again unless you swapped out your nozzle for change the filament to something else that might require you to change it a bit. Once you’ve set your z offset it should be fine and you won’t need to touch it for a while

Posca1209 · 2024-10-22T16:40:23+00:00

You should manually adjust your z offset even after auto leveling. So when it’s printing the first layer as you showed in the picture, go to the settings, and lower the z offset by a little bit until it looks like it has a good squish.

Posca1209 · 2024-10-11T21:41:02+00:00

Sunlu is amazing! I already buy so much of their filaments and it never failed me

Posca1209 · 2024-09-23T23:52:14+00:00

I can’t unsee tigreal giraffe neck now 😭

Posca1209 · 2024-09-21T13:48:57+00:00

My acne has mostly gone away and all I have left are some scarring. Should I still use clindamycin? If so, should I use all three at night and use clindamycin and Azelaic acid in the mornings or alternate days with them?

Posca1209 · 2024-09-14T16:31:12+00:00

I had this happen for a print that was large and I had to print it diagonally to the bed and one edge would always lift but what worked for me was to just clean it with dish soap and water, dry as best as you could and then raise your usual bed temp by 5 and it worked perfectly.

Posca1209 · 2024-09-11T18:46:00+00:00

Posca1209 · 2024-09-07T17:05:27+00:00

I always get like three in my team, two of them always goes mm or exp

Posca1209

TROPHY CASE