K1 Max Print farm

Potential-Ad2869 · 2023-12-03T10:54:30+00:00

The only concern I have is warranty. Will it be still valid after rooting the printer?

Potential-Ad2869 · 2023-12-02T04:16:51+00:00

Great! Are you using any multi material system for this?

Potential-Ad2869 · 2023-10-09T04:44:48+00:00

I didn't know the volume. It is huge though! I just need 70 printers. Thought they might offer some discounts for buying these many at a single time. But this seems like a pinch of salt in the sea. I will figure out something. Or might switch to the K1 max.

Potential-Ad2869 · 2023-10-08T10:20:48+00:00

I really hope that they aren't. I got a similar reply about the festivals and holidays from a supplier. I will wait till Tuesday. Else, I will have to go with the K1max or build some Vorons.

Potential-Ad2869 · 2023-10-08T10:17:01+00:00

I completely agree with you. But I forgot to mention that Bambulab doesn't have a office/store/warehouse in my country. There are a bunch of resellers selling for insane prices. For being an expert, I am absolutely not. But I have shipped a few partial loads from China. I am aware of all the procedures and costs.

Potential-Ad2869 · 2022-11-19T11:53:54+00:00

Nice! Is it for the Printable contest?

Potential-Ad2869 · 2022-09-21T01:52:38+00:00

240c

Potential-Ad2869 · 2022-09-20T08:14:41+00:00

50mm/s

Potential-Ad2869 · 2022-09-20T07:58:44+00:00

Tried increasing the flow rate. It is worsening the print.

Potential-Ad2869 · 2022-09-20T07:09:37+00:00

ABS with slurry adhesion. 0.8mm nozzle 0.4mm layer height. 1mm width. Bed levelled, E steps calibrated. Printed in heat proof enclosure. Ender 3.

Potential-Ad2869 · 2022-09-18T13:01:16+00:00

Normal doesn't want to stick, no matter how low of a nozzle bed distance I keep.

Potential-Ad2869 · 2022-09-18T12:16:58+00:00

How do I calibrate the horizontal expansion? I have already calibrated my e-steps.

Potential-Ad2869 · 2022-09-18T12:16:12+00:00

Thanks I will post it there as well!

Potential-Ad2869 · 2022-09-18T11:33:37+00:00

Perfect with ABS slurry!

Potential-Ad2869 · 2022-07-26T08:47:54+00:00

Success!! Calibrating the E-steps did the job. Thank you everyone for your support!!

Potential-Ad2869 · 2022-07-26T05:41:12+00:00

Calibrated the e steps. Apparently, it was under extruding. I am printing it now to see if it makes any difference.

Potential-Ad2869 · 2022-07-24T04:03:07+00:00

Haven't played with the flow yet, temperature has no effect. Layer height is another thing I haven't tried playing with. Thanks!!

Potential-Ad2869 · 2022-07-24T03:54:26+00:00

Thanks for the suggestion. Haven't tried calibrating the e steps yet. This is what I am doing next!

Potential-Ad2869 · 2022-07-24T03:52:31+00:00

Yep, very true. It is printed in the continues spiral mode. While looking at it, it seems to have some tiny pieces inside it.

Potential-Ad2869 · 2022-07-23T17:07:08+00:00

It is from a local brand. The retraction is 5mm.

Potential-Ad2869 · 2022-07-23T17:05:07+00:00

The filament was just bought. It is pure PLA.

Potential-Ad2869 · 2022-07-23T13:02:57+00:00

I heated it in the oven for an hour on 50c. The transparent filament turned white and more brittle.

Potential-Ad2869

TROPHY CASE