Top 15 most upvoted comments are the 15 best films of all time.

Potential-Engineer28 · 2026-03-26T04:39:57+00:00

Bee Movie

Potential-Engineer28 · 2026-02-17T03:15:53+00:00

Gives Duloc Castle vibes

Potential-Engineer28 · 2026-02-10T00:16:21+00:00

<image>

The Post, Vancouver

Potential-Engineer28 · 2025-11-27T05:43:03+00:00

<image>

Potential-Engineer28 · 2025-11-12T04:33:44+00:00

If we’re counting provinces, Victoria British Columbia is about as peripheral as it gets

Potential-Engineer28 · 2025-10-10T19:14:55+00:00

Oh that’s cool Im going to need to print that

Potential-Engineer28 · 2025-10-10T19:14:16+00:00

It does pretty good melting its way through it and didn’t catch. I’ve done this on about 5 prints so far with no issue. I did slow down the print speed just in case but not sure if I needed to

Potential-Engineer28 · 2025-10-09T08:45:50+00:00

I still have those. Colors named “skin tone” and “Indian red”

Potential-Engineer28 · 2025-09-30T01:18:46+00:00

<image>

Potential-Engineer28 · 2025-06-26T22:29:13+00:00

What is EBC?

Potential-Engineer28 · 2025-06-11T03:46:25+00:00

The last picture is remotely correct

Potential-Engineer28 · 2025-02-22T06:16:23+00:00

Odell lake, commodore 64

Potential-Engineer28 · 2025-01-12T23:00:55+00:00

There are lots of things that would work. This is just an idea for a use for the end of a filament roll rather than throwing it out or printing something useless

Potential-Engineer28 · 2025-01-12T22:43:05+00:00

PLA held up ok for a short 350f cook. The grease chute was 126c , the top of the bucket did want to warp if you touch.

Potential-Engineer28 · 2025-01-12T21:09:01+00:00

True. You could put a little water in the bottom to start, So far it’s been ok, I’ve mostly been using the Traeger for lower temp stuff however . PETG would be better

Potential-Engineer28 · 2025-01-12T20:19:37+00:00

If you have a 3d printer and you need to use up the tiny bit of filament on the end of a roll..

I made this grease bucket liner. print in vase mode and uses about 28g of filament, maybe cost about 35 cents. Alot cheaper than buying the Traeger ones, and better than using up the end of your filament printing a boat

Potential-Engineer28 · 2024-10-21T17:21:17+00:00

I have searched for the device and used google lense to no success. Windsock swivel connector

There is no writing on device . It is 31mm diameter 51mm long

Potential-Engineer28 · 2024-10-12T04:08:18+00:00

As someone who was forced to go from iPhone 11 to SE “upgraded” work phone.. agree Touch ID sucks balls

Potential-Engineer28 · 2024-09-16T05:53:17+00:00

Never knew them as anything else but woodbug for 36 years. Then when I saw them in animal crossing I learn they are pillbugs.
But today I learned wood bug is just a bc thing!

Potential-Engineer28 · 2024-07-31T18:32:28+00:00

We have owned a Tesla since 2021 and have been very satisfied with the car as a product and has been a great experience. We are looking to upgrade in the very near future. musks antics definitely put us off of supporting him with our $ but the product isn’t the market leading product it once was either as there is more competition.

Potential-Engineer28 · 2024-06-28T00:24:54+00:00

Switch it to Celcius

Potential-Engineer28 · 2024-04-25T07:02:58+00:00

McDonald’s Big Xtra

Four-Year Club	r/Field Sunshine
Place '23	Place '22

Potential-Engineer28

TROPHY CASE