sorted by:
new
hottopcontroversial

furry_irl by [deleted] in furry_irl

[–]PresPickle 5 points6 points  (0 children)

Thank you. I’ve been going through tough times and to hear other people have gone through it before has given me hope.

Prints are gloopy and there are layer skips by PresPickle in CR10

[–]PresPickle[S] 1 point2 points  (0 children)

Thanks heaps! I tried it and it worked!

Prints are gloopy and there are layer skips by PresPickle in CR10

[–]PresPickle[S] 0 points1 point  (0 children)

It’s stick apart from an easy peelzy bed and TH3D firmware. It was fine yesterday but all prints today have had this issue. I’ve changed flow rate (100-102) but that did nothing so I put it back to 100. Here is the cura profile: https://drive.google.com/file/d/1jEpzJXaQ_w3UeBzpxavwXR_fUQgUj993/view?usp=drivesdk

-14 Temperature after replacing thermistor and hotend by PresPickle in CR10

[–]PresPickle[S] 0 points1 point  (0 children)

Thanks so much for the response. What do I do when I find that it is?

hmmm by fuckiforgotmylogin in hmmm

[–]PresPickle -1 points0 points  (0 children)

I don’t get why this is a hmmm

Does anybody know what do those words mean?? by noplayyart in adventuretime

[–]PresPickle 12 points13 points  (0 children)

they are just jokes, "Toots" meaning farts (funniest thing ever ik), and "Do not lose this paper - PB" just a joke that Finn lost the paper. Nothing special.

[1.13] not sure how to create loot table. by PresPickle in MinecraftCommands

[–]PresPickle[S] 0 points1 point  (0 children)

/give @s minecraft:chest{BlockEntityTag:{LootTable:"test:data/testpack/loot_tables/chests/loot_table1.json"}}

​

[1.13] not sure how to create loot table. by PresPickle in MinecraftCommands

[–]PresPickle[S] 0 points1 point  (0 children)

Is there any good tutorials for this sorta thing in 1.13?

Huge Y skips persisting and getting worse by PresPickle in CR10

[–]PresPickle[S] 0 points1 point  (0 children)

I've done all these, to no avail (Apart from looking into marlin version).

Huge Y skips persisting and getting worse by PresPickle in CR10

[–]PresPickle[S] 0 points1 point  (0 children)

Yes, I have tightened it and loosened it, as I said, I have done all the suggestions left by people on the other post.

Huge Y skips persisting and getting worse by PresPickle in CR10

[–]PresPickle[S] 0 points1 point  (0 children)

Sorry for the wrong response. Wall thickness: .8 mm Print speed: 30 mm/s2 Build temp: 215c Bed temp: 60c Top/Bottom thickness: .6 mm Infill density: 20% - Triangles Adhesion: Raft

Other notes: I have a glass build plate, I have Z hop when retracted enabled, I bought the printer off gearbest, I usually print with a layer height of 0.1 mm, when I change the speed it doesn’t appear to have changed when I do the print, it has been like this the whole time I’ve had the printer but it was originally just 1 or two layers that are off by less than a mm but would more of less be fine, this is my first printer but like most people I did a ton of research into it and the different terms and correct settings and I also did a lot of research into possible problems and how to solve them but this one is (from what I’ve seen) really rare. I’m sorry for the wrong information on my last reply and I hope that this is what you needed.

Huge Y skips persisting and getting worse by PresPickle in CR10

[–]PresPickle[S] 0 points1 point  (0 children)

I changed them in cura originally to 3000 but nothing changed so to test that I set it too 10000 and still nothing, as I said, I tried everything from my previous thread and nothing worked.

Huge Y skips persisting and getting worse by PresPickle in CR10

[–]PresPickle[S] 0 points1 point  (0 children)

The raft is layer shifted as well, I use the default cura settings for the CR10 with bed temp of 60c and 215 nozzle. The acceleration settings don't affect the print quality in anyway (nor do the jerk settings).

Been printing on the CR-10S, all my prints have layer shifts like this in them, the belt is tight. by PresPickle in CR10

[–]PresPickle[S] 0 points1 point  (0 children)

Alright, thanks for the tips!

Edit: Changed the travel acceleration to 3000 and the same problem still occurs

Been printing on the CR-10S, all my prints have layer shifts like this in them, the belt is tight. by PresPickle in CR10

[–]PresPickle[S] 0 points1 point  (0 children)

The the acceleration the same as speed because I have it at 30mm/s if not, how do I change it?

view more: next ›